Gladiator GAWT08BTTM Handleiding
Gladiator
Niet gecategoriseerd
GAWT08BTTM
Bekijk gratis de handleiding van Gladiator GAWT08BTTM (7 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.7 sterren uit 1.5 reviews. Heb je een vraag over Gladiator GAWT08BTTM of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/7
12
BASE TRIM
INSTALLATION
INSTRUCTIONS
GARNITURE
PLINTHE
INSTRUCTIONS
D'INSTALLATION
LOS
CONTRAMARCOS
INSTRUCCIONES
DE INSTALACIÓN
In U.S.A. call: 1-866-342-4089
Aux États-Unis, composer le: 1866342-4089
En los EE.UU., llame al: 1-866-342-4089
W11740988A
In Canada call: 1-800-807-6777
Au Canada, composer le: 1800807-6777
En Canadá, llame al: 1-800-807-6777
www.gladiatorgarageworks.com
www.gladiatorgarageworks.ca
TABLE OF CONTENTS/ TABLE DES MATIÈRES /ÍNDICE
Model
GAWT08BTTM - Smoke
Modèle
GAWT08BTTM - Fumée
Modelo
GAWT08BTTM - Humo
BASE TRIM INSTALLATION
INSTRUCTIONS 2 ......................................
Tools and Parts 2 .....................................
Base Trim Requirements 2 .......................
Screw Requirements 2 .............................
Install the Base Trim 2 ..............................
WARRANTY 2 .............................................
GARNITURE DE PLINTHE -
INSTRUCTIONS D'INSTALLATION 3 .......
Outillage et pièces 3 .............................
Garniture de plinthe - Critères à
respecter 3 ..............................................
Vis - Critères à respecter 3 .....................
Installation de la garniture de plinthe 4 ...
GARANTÍE 4 ..............................................
INSTRUCCIONES DE INSTALACIÓN DE
LOS CONTRAMARCOS 5 .........................
Piezas y herramientas 5 ...........................
Requisitos para los contramarcos 5 ........
Requisitos de los tornillos 5 .....................
Instalación del contramarco 6 .................
GARANTÍA 6 ...............................................
2
BASE TRIM INSTALLATION INSTRUCTIONS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed:
■Level ■Stud finder
■Tape measure ■AC nder
■Drill ■Square
■Saw ■Pencil
■Screws (galvanized or
all-weather)
Additional Tools and Parts Needed for Masonry Block/Poured
Concrete Wall Installation:
■3/16" x 1¾" Flat-head
masonry screws
■Caulk gun
■Hammer drill ■Construction adhesive
■5/32" Masonry drill bit
NOTE: Gladiator
®
Base Trim can be cut and drilled with ordinary
woodworking equipment.
Base Trim Requirements
■Gladiator
®
Base Trim can be mounted directly to masonry
wall, over drywall to wooden studs, or to bare wooden studs.
■Intended for use in a garage or basement.
NOTE: Before installing GearWall
®
Panels to basement
walls, you must waterproof the basement to prevent mildew
and foundation damage. Walls that appear dry may actually
become damp when enclosed by paneling. Install the panels
in accordance with all local codes and ordinances.
Screw Requirements
IMPORTANT: Use correct screw length for your wall type. See
chart following.
Screw
Screw for Wall Type Length
length* Wall
Masonry Bare
Studs
Wooden
1/2"
Dr allyw over Wood Studsen
5/8"
(1.27 cm)
3/4"
(1.6 cm) (1.9 cm)
#8 X 1¹⁄₄"
#8 X 2"
3/16" X 1 ³⁄₄ "
* r bare w den st s covered wa , use a weat r at dFo oo ud and ll an ll he fl-hea
d k screw. r co rete blo poured masonryec Fo nc ck and , use a at adfl-he
masonry screw.
Install the Base Trim
To achieve a more nished appearance at the seams and
corners, cut the ends of each piece of base trim at a 45° angle to
create a miter joint.
Masonry Block/Poured Concrete Wall
1. Use a level to position the Base Trim at the desired height on
the wall.
2. Drill a hole through the Base Trim and into the wall surface.
3. Attach the Base Trim to the wall by placing 3/16" x 1¾"
Flat-head masonry screws every 48" (121.92 cm).
NOTE: For extra hold, you may apply construction adhesive
to the Base Trim before attaching it to the wall.
4. Repeat this process for the next section of base trim.
Drywall over Wooden Studs or Bare Wooden Studs
1. Locate all wooden studs and electrical wiring. Mark the
wall(s).
IMPORTANT: Compare screw length to electrical wire
locations. Be sure the screw will not pierce electrical wiring.
2. Base Trim should be mounted to the wall so that it begins and
ends at wooden studs. Measure from the edge of the stud at
the beginning of the desired coverage area to the center of
the last wooden stud that is within 4 ft (1.22 m).
3. If necessary, cut the rst section to this length.
4. Check that the Base Trim is level. Then place a screw every
48"(121.92 cm).
NOTE: Drive the screws through the base trim until the heads
are ush. If splitting occurs, predrill and countersink the
screw holes near section ends.
5. Repeat this process for the next section of base trim.
A
B
C
D
E
B
A. Drywall D. 1" (2.54 cm) min. to
1¼" (3.17 cm) max. if
near wiring
B. Flat-head screw E. 5/8" (1.6 cm)
C. Wooden stud
IMPORTANT: Compare screw length to electrical wire locations.
Be sure the screw will not pierce electrical wiring.
3
WARRANTY
For warranty information:
In the U.S.A. call or visit our website at1-866-342-4089
www.gladiatorgarageworks.com
In Canada call or visit our website at1-800-807-6777
www.gladiatorgarageworks.ca
Product specificaties
| Merk: | Gladiator |
| Categorie: | Niet gecategoriseerd |
| Model: | GAWT08BTTM |
Heb je hulp nodig?
Als je hulp nodig hebt met Gladiator GAWT08BTTM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Gladiator
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
Handleiding Niet gecategoriseerd
- NICEDACK
- Bebob
- Mission Air
- JLab
- DSC
- IDIS
- On Air
- Williams Sound
- Sitecom
- Turbo Scrub
- Naim
- Juniper
- Fanvil
- Steelplay
- Cudy
Nieuwste handleidingen voor Niet gecategoriseerd
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025