Geonaute G-Eye 2 WiFi Remote Handleiding

Geonaute Digitale camera G-Eye 2 WiFi Remote

Lees hieronder de 📖 handleiding in het Nederlandse voor Geonaute G-Eye 2 WiFi Remote (5 pagina's) in de categorie Digitale camera. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
1
EN G-Eye 2
WiFi Remote
WAIT HOST PBC PRESS CONNECT
info SYNC
CONNECT
100-088
2H30
1080P- 50
Power indicator
(red) WiFi status indicator (blue)
Screen
On/off button - Video recording
button
Shutter button
Stop recording video
button
Loop for the strap
Wide angle of view
Medium angle of view
Narrow angle of view
Small angle of view
USB port
REMOTE CONTROL DESCRIPTION
The remote control has a battery life of 5 hours maximum.
Recharging takes approximately 2 hours.
2h
12
6
39
CHARGING THE BATTERY
2
1Switch on the camera and activate its WiFi function
2On the remote control, start by pressing the " " button, and press
the " " button at the same time. Keep holding these two buttons
until the remote control displays the screen opposite.
WAIT HOST PBC
3Push the " " button on the camera and wait 20-30 seconds, until
the remote control displays the screen opposite.
PRESS CONNECT
4Push the " " button on the remote control and wait 20-30 seconds,
until the remote control displays the screen opposite. info SYNC
CONNECT
5The blue indicator light on the remote control will then start blinking,
and conî‚¿guration information is in the process of synchronising
between the remote control and the camera. Wait for approximately
20 seconds for the camera's status to appear on the remote control:
100-088
2H30
1080P- 50
CAUTION: For a connection to be possible, the pairing procedure must be performed î‚¿rst.
1Press the On " " button for 5 seconds.
2The remote control automatically scans to look for the camera it is
meant to pair with.
3Once the camera has been found and correctly connected, the
screen on the remote control will display the camera's status.
100-088
2H30
1080P- 50
4You can now use the remote to control the camera.
5To turn off the remote control, press the Off button for 5 seconds.
PAIRING PROCEDURE
CONNECTING THE REMOTE CONTROL
3
PRECAUTIONS FOR USE
 Handle the device with care. Do not drop it or subject it to serious impacts.
 This product conforms to the IP66 watertightness protection rating standard, meaning that it
can be exposed to rain, but cannot be submerged in water.
 For greater safety, avoid handling the buttons while in use. Lapses in concentration can be
dangerous.
 Do not dismantle the product, as this could cause damage and void the warranty.
 Using this product in very cold conditions (temperatures below -10°C) could decrease the
battery’s capacity, and in turn the amount of time the product can be used.
• Press and hold for 5 seconds to turn the remote control on/off.
• If the camera is in video mode, press once to begin recording a video.
• If the camera is in photo mode, press once to go to video mode.
• If the camera is in photo mode, press once to take a photo.
• If the camera is in video mode, press once to go to photo mode.
• Press once to stop the recording in progress.
X1 • Press once to choose a wide angle of view.
X2 • Press once to choose a medium angle of view.
X3 • Press once to choose a narrow angle of view.
X4 • Press once to choose a small angle of view.
X1
X4
RESETTING: In the event of an operational problem or remote control malfunction, you
can reset by pressing the X1 and X4 buttons at the same time.
FUNCTION LIST


Product specificaties

Merk: Geonaute
Categorie: Digitale camera
Model: G-Eye 2 WiFi Remote

Heb je hulp nodig?

Als je hulp nodig hebt met Geonaute G-Eye 2 WiFi Remote stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Digitale camera Geonaute

Handleiding Digitale camera

Nieuwste handleidingen voor Digitale camera