GE ZX27CTYSS Handleiding

GE Niet gecategoriseerd ZX27CTYSS

Lees hieronder de 📖 handleiding in het Nederlandse voor GE ZX27CTYSS (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

GE Monogram

Assembly Instructions

Before you Begin – Read these instructions completely and carefully.

Note To Installer: Be sure to leave these instructions with the Consumer.

Note to Consumer: Keep these instructions with your Use and Care Book for future reference.

Assembly of this grill cart requires basic mechanical

skills. Proper assembly is the responsibility of the

installer.

NOTE:

This cart must be completely assembled before any

gas connections are made.

If you have questions concerning the installation of

this product, call the GE Answer Center

® Consumer

Information Service at 800.626.2000, 24 hours a day,

7 days a week.

If you received a damaged Grill Cart, you should

contact your dealer.

Step 1:

Remove

Packaging

Open the box and remove the contents.

Remove packaging and protective film from

all parts.

Shelf Handle

Shelf

Back Brace

Bottom/Base Panel

Wheels

Front Panel

Caster with Lock

Locate the hardware accessory package and check contents.

Side Braces

Front Brace

Left Side Panel

Right Side Panel

Axle

1/4-20 x 1/2 Bolts

Count 36

32 required, 4 extra

1/4-20 x 3/4 Bolts

Count 2

no extra

Wheel Caps

Count 2

Black Plastic

Grommet

Count 1

#10 Washers

Count 12

8 required, 4 extra

1/4 Washers

Count 40

32 required, 8 extra

Self-tapping Screws

Count 2

1/4-20 Nuts

Count 36

32 required, 4 extra

10-24 Nuts

Count 10

8 required, 2 extra

Black Plastic

Bezels

Count 2

Phillips Head Screws

Count 10

8 required, 2 extra

Caster

27" Outdoor Cooking Center

Grill Cart

Model ZX27CTYSS

Installation

27" Grill Cart Assembly

• Two 7/16" wrenches

• 3/8" wrench or socket

• Phillips head screwdriver

• Rubber or wooden mallet

• Gloves to protect against sharp edges

10-24 Nuts

Phillips

Head

Screws #10 Washers

USE

EACH

• Locate the bottom/base panel and one side

brace.

• Place the front of the base towards you.

(The front side has 6 screw holes on each

side.)

• Select the caster with lock on the side.

• Place the caster below the front side of the

base, aligned with 4 screw holes.

• Place a side brace on top of the base at the

left side with screw holes aligned.

• Install 4 phillips head screws through the

caster into the base and through the brace.

• Secure screws with flat washers and nuts on

top of the brace. Do not tighten.

• Install the other caster to opposite end of

the brace following the same procedure.

Bottom Panel

1/4-20 x 1/2

Bolts 1/4 Washer 1/4-20 Nuts

USE

EACH

• Install front brace to base with 4 bolts and

washers through the top and secure with

nuts on the bottom. Do not tighten.

1/4-20 x 1/2

Bolts 1/4 Washer 1/4-20 Nuts

USE

EACH

• Install right side brace to the base by

installing 8 bolts and washers through the

top and secure with nuts on the bottom.

Again, do not tighten.

• Adjust brace alignment by tapping and

sliding until corners meet. Tighten all

screws.

CAUTION: The grill is extremely heavy. 2

people are required to lift and place the grill

onto the cart.

Tools

You Will

Need

Step 2:

Install

Casters

and Braces

to Base

Installation

27" Grill Cart Assembly

Step 3:

Install Side

Panels

to Base

• Flatten the carton to use as a pad.

• Stand the assembled base on end.

• Secure left and right side panels to the

bottom panel with 4 bolts, washers and nuts

(2 on each side). Note: Right side panel has

a hole near the center.

• Install bolt and washer from the bottom and

into the base, secure with nuts inside. Do not

tighten.

1/4-20 x 1/2

Bolts 1/4 Washer 1/4-20 Nuts

USE

EACH

Step 4:

Install

Front Panel

to Base

1/4-20 x 1/2

Bolts 1/4 Washer 1/4-20 Nuts

USE

EACH

• Place the front panel on the assembly. Install

bolt with washer from the bottom into the

base and secure with nuts. Do not tighten.

Front Panel

Side Panel

Bottom Panel

Right Side Panel

Bottom Panel

Front Panel

1/4-20 x 1/2

Bolts 1/4 Washer 1/4-20 Nuts

USE

EACH

• Stand the assembly up and bolt the front

panel to the side panels with bolts, washers

and nuts as shown. (2 on each side).

Product specificaties

Merk:	GE
Categorie:	Niet gecategoriseerd
Model:	ZX27CTYSS

Heb je hulp nodig?

Als je hulp nodig hebt met GE ZX27CTYSS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd GE

GE Profile UCG1600LWW Handleiding

6 December 2023

GE ZWSP42D Handleiding

1 Juli 2023

GE ZGW124ENSS Handleiding

11 Juni 2023

GE Profile GCG1500LBB Handleiding

5 Juni 2023

GE GNULQ Handleiding

24 Mei 2023

GE FXRC1 Handleiding

10 Mei 2023

GE ZX27CTYSS Handleiding

9 Mei 2023

GE ZKHT1 Handleiding

7 Mei 2023

GE GXEM01Z Handleiding

6 Mei 2023

GE ZCG3100VBB Handleiding

6 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024

Sony PDW-U4 Handleiding

26 April 2024

Sony NXL-FR318 Handleiding

26 April 2024

Sony NSBK-CL05 Handleiding

26 April 2024