GE ZBD7100GSS Handleiding

GE Wasmachine ZBD7100GSS

Lees hieronder de 📖 handleiding in het Nederlandse voor GE ZBD7100GSS (16 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
Monogram.
We bring good things to life.
®
If you have questions, call 800.626.2000 or visit our website at:
www.monogram.com
Installation
Instructions
Built-In Dishwashers
ZBD6400, ZBD6500, ZBD6600
ZBD6700, ZBD6900, ZBD7000,
ZBD7100
Chef’s Washers
ZBD6605, ZBD6905, ZBD7005,
ZBD7105
Design Guide with
Installation Instructions
Safety Information
• IMPORTANT – The dishwasher MUST
be installed to allow for future removal from the
enclosure if service is required.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
FOR YOUR SAFETY
Read and observe all CAUTION and WARNINGS
shown throughout these instructions.
For Monogram local service in your area,
1-800-444-1845.
For Monogram service in Canada
1-888-880-3030
For Monogram Parts and Accessories, call
1-800-626-2002.
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - Save these instructions for
local inspector’s use. Observe all governing
codes and ordinances.
• Note to Installer - Be sure to leave these instruc-
tions with the Consumer.
• Note to Consumer - Keep these instructions with
your Owner’s Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical and electrical skills. Proper installa-
tion is the responsibility of the installer. Product
failure due to improper installation is not covered
under the GE Appliance Warranty.
• Completion Time – 1 to 2 Hours. New installa-
tions require more time than replacement installa-
tions.
CONTENTS
Design Information
Product Dimensions .......................................................3
Models Available ............................................................ 3
Advance Planning .......................................................... 3
Installation Preparation
Materials You Will Need .................................................4
Tools You Will Need .......................................................4
Parts Supplied .................................................................5
Prepare Dishwasher Enclosure ..................................... 5
Drain Requirements .......................................................6
Prepare Electrical Wiring ...............................................7
Prepare Hot Water Line .................................................8
Custom Panel Dimensions
Custom Panels for ZBD6400 ......................................... 9
Custom Panels for ZBD7000, ZBD7005 ........................9
Installation Instructions
Step 1, Remove Packaging ...........................................10
Step 2, Install Leveling Legs ....................................... 10
Step 3, Remove Access Covers .................................... 10
Step 4, Install 90 Elbow ...............................................10°
Step 5, Install Power Cord............................................11
Step 6, Level Dishwasher ..............................................11
Step 7, Slide Dishwasher into Opening.......................11
Step 8, Connect Water Line ........................................ 11
Step 9, Connect Drain Line ........................................ 12
Step 10, Connect Electrical ......................................... 12
Step 11, Position and Level Dishwasher ......................13
Step 12, Pre-Test Check List........................................ 13
Step 13, Dishwasher Wet Test ..................................... 13
Step 14, Secure Dishwasher
to Cabinet or Countertop ....................................... 14
Step 15, Install Toekick, Custom Toekick .................. 14
Step 16, Install Side Trim Strips ..................................14
Panel Installation for Models
ZBD7000 and ZBD7005............................................15
Design Information
3
ADVANCE PLANNING
• These dishwashers are designed for versatility,
adaptable to virtually any installation.
• All models have a full length door or a modified
door to accept a full cabinet panel without the
traditional access panel
• Side tub flange trim is adjustable and will conceal
any slight gap between the dishwasher and adjacent
cabinetry.
• These dishwashers may be installed beneath
countertops of stone or other materials that will not
accept screws. No trim kit required.
Standard installation in 24" deep cabinets
• In standard 24" deep cabinets, the dishwasher door
will be flush with adjacent cabinetry.
• Models with 3/4" thick custom door panel will fit
flush with adjacent cabinetry.
Supplied or Custom Toekicks
• A 2-piece toekick is supplied with all models. The
toekick is height and depth adjustable.
• Depending on cabinetry style, a custom toekick can
also be installed to match cabinetry. Care must be
taken to assure door swing clearance above the
toekick.
• A notched continuous toekick may be necessary to
allow a long door panel, on models ZBD7000 and
ZBD7005, to swing back and under the dishwasher.
ADA-Compliant
Installation below 34" high countertops
A reduced height installation (32-1/2" min.) beneath
a 34" countertop, can be accomplished by removing
the front leveling legs. The rear legs should be
screwed in flush with the bottom support, as shipped.
The front of the dishwasher must be shimmed to
level the dishwasher. Water and electrical must be
routed through the back wall.
• All models are ADA-Compliant. Models ZBD7000
and ZBD7005 offer even more installation and
design flexibility because the required custom door
panel may be sized from 26-1/4 to 30-1/4" height.
See page 9 for details.
PRODUCT DIMENSIONS
DISHWASHER MODELS
Traditional Built-In
ZBD6400 BB, Black - Accepts 1/4" or 3/4" custom
panels
ZBD6400 WW White - Accepts 1/4" or 3/4" custom
panels
Trim Kits for models ZBD6400
• ZPF625W (white) or ZPF625B (black) custom panel
kits, supports a 1/4" thick custom door panel.
• ZPF675W (white) or ZPF675B (black) custom panel
kits support a 3/4" thick custom door panel.
Traditional Built-In
ZBD6500 SS, Stainless steel door
Professional Series
ZBD6600 SS, Stainless Steel
Fully Wrapped
ZBD6700 BB, Black
ZBD6700 WW, White
ZBD6900 SS, Stainless steel with black controls
Fully Integrated
ZBD7000 II, Requires custom panel and handle
ZBD7100 SS, Stainless steel with tubular handle
CHEF’S WASHER MODELS
Professional Series
ZBD6605 SS, Stainless steel
Fully Wrapped
ZBD6905 SS, Stainless steel
Fully Integrated
ZBD7005 II, Requires custom panel and handle
ZBD7105 SS, Stainless steel with tubular handle
23-7/8"
*24"
34"
Adjustable
to 35"
*Dishwasher model
ZBD7000 and
Chef’s Washer
model ZBD7005
require a 3/4" thick
custom panel and
will be 24-3/4"
deep.


Product specificaties

Merk: GE
Categorie: Wasmachine
Model: ZBD7100GSS

Heb je hulp nodig?

Als je hulp nodig hebt met GE ZBD7100GSS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wasmachine GE

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine