GE GPF525W Handleiding
GE
Vaatwasser
GPF525W
Bekijk gratis de handleiding van GE GPF525W (4 pagina’s), behorend tot de categorie Vaatwasser. Deze gids werd als nuttig beoordeeld door 4 mensen en kreeg gemiddeld 4.5 sterren uit 2.5 reviews. Heb je een vraag over GE GPF525W of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
GE Consumer & Industrial
Appliances
Installation Instructions
Dishwasher 1/4" Custom Panel Trim Kit
GPF525 Series
GPF525B-Black Trim Kit, GPF525C-Bisque Trim Kit, GPF525W-White Trim Kit
IMPORTANT – Save these instructions for local
inspector’s use.
IMPORTANT – Observe all governing codes and
ordinances
Note to Installer – Be sure to leave these instructions with
the Consumer.
Note to Consumer – Keep these instructions with your
Owner’s Manual for future reference.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
WARNING:
To prevent electric shock, disconnect electrical power
supply to dishwasher before changing panels. Do not
operate dishwasher while changing panels or when
toekick assembly is removed.
TOOLS AND MATERIALS REQUIRED:
• 1/4" socket driver
• Phillips screwdriver
• Electric drill
• 1/8" drill bit
• Masking tape
• Safety Glasses
• Gloves to protect against sharp edges
KIT INCLUDES:
• Installation Instructions
• Left, right, top and bottom door trim
• 8 – 18 x 5/16" color-matched screws
IMPORTANT!
The factory supplied door springs must
be replaced with two WD03X10012 door
springs if the custom panel weighs more
than 3.5 pounds. Order these springs at
GE.COM or call 1-800-626-2002. Refer to
Step 4 for more information
STEP 1: CUT 1/4" THICK CUSTOM PANELS TO SIZE
• Cut door panel to the dimensions shown.
NOTE: The trim provided will conceal the cut edges of the
panels.
STEP 2: REMOVE TOEKICK ASSEMBLY
• Make sure electrical power to the dishwasher is turned off.
• Remove the two toekick panel screws and toekick panel. Set
them aside for use in Step 6.
NOTE: Do not remove the insulation behind the toekick.
2
INSTALLATION OPTIONS
This trim kit is designed to accommodate 1/4" thick panels.
A raised panel screwed or glued to 1/4" thick backing can be
used. The raised portion of the panel must be fabricated to
permit clearances for the trim on all sides.
A 3/4” thick custom panel may be installed by routing the top
and sides to 1/4" thickness.
3
STEP 3: INSTALL DOOR PANEL TRIM AND CUSTOM PANEL
A
B
C
• Place bottom trim against the bottom of the door panel and
drive center screw, then left and right screws. Use the
8 - 18 x 5/16" color-matched screws provided.
• Slide “Z” shaped trim under the escutcheon.
• Slide custom door panel under the “Z” trim
and bottom trim.
• The notch on the side trim pieces goes towards the front.
Slide side trim up and under the escutcheon and over the
edge of the custom panel.
D
E
• Use masking tape to hold trim tightly against the custom
panel.
F
• Use the holes in the side trim pieces to locate, center punch,
and then drill 1/8" holes in the dishwasher panel. Use care
when performing this operation to prevent damage to the
side trim.
• Fasten the trim to the dishwasher door panel with the
8 - 18 x 5/16" color-matched screws.
• Remove tape.
Drill 1/8" Holes
and Install Screws
Escutcheon
Product specificaties
| Merk: | GE |
| Categorie: | Vaatwasser |
| Model: | GPF525W |
Heb je hulp nodig?
Als je hulp nodig hebt met GE GPF525W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Vaatwasser GE
10 Augustus 2025
10 Augustus 2025
30 Januari 2025
30 Januari 2025
30 Januari 2025
30 Januari 2025
30 Januari 2025
28 Januari 2025
28 Januari 2025
28 Januari 2025
Handleiding Vaatwasser
- Schaub Lorenz
- De Dietrich
- IFB
- Fagor
- Parmco
- Delonghi
- Emerio
- Trieste
- OK
- FORS
- Smeg
- La Germania
- Holland Electro
- Continental Edison
- Kuppersbusch
Nieuwste handleidingen voor Vaatwasser
12 September 2025
12 September 2025
10 September 2025
10 September 2025
9 September 2025
9 September 2025
8 September 2025
8 September 2025
8 September 2025
8 September 2025