GE GHDA480NBB Handleiding

GE Wasmachine GHDA480NBB

Lees hieronder de 📖 handleiding in het Nederlandse voor GE GHDA480NBB (16 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
GE Consumer & Industrial
Appliances
s
t
a
a
t
o
n
s
r
c
t
o
s
Bu
ilt-In Dishwasher
f you have questions, call 800.GE.CARES (800.432.27
37) or visit our website at
: www.ge.com
IMPORTANT
– The dishwasher MUST be installed
to allow for future removal from the enclosure if service is
required.
f you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for available
custom panel kits.
FOR YOUR SAFETY
Read and observe all CAUTIONS and WARNINGS shown
throughout these instructions. While performing
installations described in this booklet, gloves, safety glasses
or goggles should be worn.
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
IMPORTANT
– Observe all governing codes and
ordinances.
•
Note to Installer
– Be sure to leave these instructions for the
consumer’s and local inspector’s use.
•
Note to Consumer
– Keep these instructions with your
Owner’s Manual for future reference.
•
Skill Level
– Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills.
Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See warranty information.
•
Completion Time – 1 to 3 Hours
. New installations require
more time than replacement installations.
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
TOOLS YOU WILL NEED:
®
Phillips head screwdriver
®
1/4" and 5/16" nutdriver
®
6" Adjustable wrench
®
Level
®
Carpenters square
®
Measuring tape
®
Safety glasses
®
Flashlight
®
Bucket to catch water when fl ushing the line
®
15/16" socket (optional for skid removal)
®
Gloves
For New Installations Only:
®
Tubing cutter
®
Drill and appropriate bits
®
Hole saw set
90° Elbow,
Ferrule and
Compression Nut
Wire Nuts (3)
Waste Tee
Electrical Cable
(or Power Cord, if applicable)
Hot Water Line
Hand
Shut-Off
Valve
Side and Top Trim Pieces on some models
Hole Saw Set
Level
Thread
Seal Tape
Air Gap
Drain Hose
Hose Clamp
1/4" and 5/16"
Nutdriver
15/16" Socket
Bucket
Tubing Cutter
Drill and Bits
Flashlight
Gloves
Phillips
Head
Screwdriver
Carpenters
Square
6"
Adjustable
Wrench
Safety Glasses
Installation Preparation
Drain Hose Hanger
Measuring Tape
PARTS SUPPLIED
IN INSTALLATION PACKAGE:
Two #8-18 x 5/8" Phillips special head screws, to
secure dishwasher to underside of countertop.
Junction box cover and #10 hex head screw
Hose Clamp
Drain hose (approximately 78" long)
Drain hose hanger
Side and top trim pieces (some models)
Literature, samples and/or coupons
MATERIALS YOU WILL NEED:
Ferrule, compression nut and 90° Elbow (3/8"NPT
external thread on one end, opposite end sized
to fit water supply)
Thread seal tape
UL Listed wire nuts (3)
GPF65 side mount kit if countertop is
granite or similar material
Materials Needed for
New Installations:
Air gap for drain hose, if required
Waste tee for house plumbing, if applicable
Electrical cable or power cord
Screw type hose clamp
Strain relief for electrical connection
Hand shut-off valve (recommended)
Water line–3/8" minimum copper tubing
GPF10L drain hose
(10' long
, if needed
Junction
Box Cover
GPF65
Side-Mount
Bracket Kit
#8 Phillips
Special
Head Screws
5/8" long
Screw Kit
#10
Hex- Head
J-Box Screw
1/2" long
Optional
10' Drain Hose
GPF10L
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when required by local codes and ordi-
nances. The air gap must be installed according to manufacturer’s
instructions.
PREPARE DISHWASHER ENCLOSURE
• The rough cabinet opening must be at least 24" deep, 24"
wide and approximately 34-1/2" high from floor to underside
of the countertop.
CLEARANCES:
When
installed into a corner,
allow 2" min. clearance
between dishwasher
and adjacent cabinet,
wall or other appliances.
Allow 28-3/8" min. clear-
ance from the front of
the dishwasher for door
opening. Figure B
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 10' distance to drain.
NOTE:
Air gap must be used, if waste tee or disposer
connection is less than 18" above floor to prevent siphoning.
DETERMINE DRAIN METHOD
The type of drain installation depends on the following
questions.
®
Do local codes or ordinances require an air gap?
®
Is waste tee less than 18" above floor?
If the answer to either question is YES, Method 1 MUST
be used.
• If the answers are NO, either method may be used.
CABINET PREPARATION
• Drill a 1-1/2" diameter hole in the cabinet wall within
the shaded areas shown in Figure A for the drain hose
connection. The hole should be smooth with no sharp edges.
IMPORTANT
–
When
connecting drain line to disposer,
check to be sure that drain plug has
been removed. DISHWASHER WILL
NOT DRAIN IF PLUG IS LEFT IN PLACE.
Method 2 – “High Drain Loop” with Waste Tee or Disposer
Tip: Avoid unnecessary service call charges
Always be sure disposer drain plug has been removed before
attaching dishwasher drain hose to the disposer.
Figure D
• The dishwasher must be installed so that drain hose is no
more than 10' in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides and
back, and must not support any part of the enclosure.
24"
Min.
This Wall Area
must be Free
of Pipes or
wires
Plumbing and Electric Service
Must Enter Inside This Area
34-1/2"1/4"
Underside of
Countertop
to Floor
4"
24"
Min.
6"
5" 5"
4"
Cabinets
Square
and
Plumb
Floor MUST be Even
With Room Floor.
32"
Min.
18"
Min.
Drain Hose Hanger
Figure B
Clearance for Door
Opening 2" Minimum
Countertop
Dishwasher
28-3/8"
Figure C
Installation Preparation
3
Remove
Drain
Plug
WARNING
To reduce the risk of electric shock,
fi re, or injury to persons, the installer
must ensure that the dishwasher is
completely enclosed at the time of
installation.
32"
Min.
18"
Min.
Drain Hose Hanger

Product specificaties

Merk: GE
Categorie: Wasmachine
Model: GHDA480NBB

Heb je hulp nodig?

Als je hulp nodig hebt met GE GHDA480NBB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Wasmachine GE

GE

GE PDP755SBVTS Handleiding

16 Maart 2024
GE

GE GTW480ASWWB Handleiding

16 Maart 2024
GE

GE PDT755SYVFS Handleiding

16 Maart 2024
GE

GE PDT795SYVFS Handleiding

16 Maart 2024
GE

GE GTW525ACWWB Handleiding

16 Maart 2024
GE

GE PDT795SBVTS Handleiding

16 Maart 2024
GE

GE GTW220ACWWW Handleiding

16 Maart 2024
GE

GE GTW385ASWWS Handleiding

16 Maart 2024
GE

GE PDT755SBVTS Handleiding

16 Maart 2024
GE

GE GTW325ASWWW Handleiding

16 Maart 2024

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine

Winia

Winia WVD-A08T1WK14B Handleiding

28 April 2024
Continental Edison

Continental Edison CELL7140IB Handleiding

28 April 2024
Bauknecht

Bauknecht WAT Smart Eco 12C Handleiding

27 April 2024
Bauknecht

Bauknecht B7 89 SILENCE EE Handleiding

27 April 2024
BEKO

BEKO WTE 7512 BSS Handleiding

26 April 2024
MPM

MPM -4610-PH-04 Handleiding

25 April 2024
Samsung

Samsung WW11DB8B95GH Handleiding

25 April 2024
Sôlt

Sôlt GGSFLW800W Handleiding

22 April 2024
Whirlpool

Whirlpool ZEN FSCR70421 Handleiding

21 April 2024
Samsung

Samsung WW90T4540TE Handleiding

18 April 2024