Garmin LiveScope 2 LVS42HD Handleiding
Pagina's 16 Visvinder
Bekijk de handleiding van Garmin LiveScope 2 LVS42HD gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
LIVESCOPE
™
2 TRANSDUCER
Installation Instructions
Important Safety Information
WARNING
See the guide in the chartplotter product box for product warnings and Important Safety and Product Information
other important information.
You are responsible for the safe and prudent operation of your vessel. Sonar is a tool that enhances your
awareness of the water beneath your boat. It does not relieve you of the responsibility of observing the water
around your boat as you navigate.
CAUTION
Failure to install and maintain this equipment in accordance with these instructions could result in damage or
injury.
NOTICE
For the best possible performance and to avoid potential damage to the device or to your vessel, you must
install this device according to these instructions.
Read all installation instructions before proceeding with the installation. If you experience difficulty during the
installation, go to for more information.support.garmin.com
Software Update
You must update the Garmin
®
chartplotter software when you install this device. For instructions on updating
the software, see your chartplotter owner's manual at .support.garmin.com
Installation Support Videos
You can view videos online for assistance when installing this device.
You can access the videos by going to in your web browser or by scanning garmin.com/videos/lvs2
this QR code with your smartphone.
Tools Needed
•Flat screwdriver or 8mm wrench or socket to install the barrel mount clamp
•Electrical tape (preferred) or cable ties
Parts Bags
The installation hardware for the transducer is included in labeled bags. As you complete the installation
process, each procedure begins with a reference to the label on the parts bag needed to complete the
procedure. You can use this table to review or verify the parts bags needed for the installation procedures.
NOTE: You should leave all parts in the labeled bags until the instructions advise you to open a specific bag. Not
all hardware is used for all installation types.
Contains parts needed when installing the side shaft mount
Contains parts needed when installing the barrel mount
Contains parts needed when installing the perspective, shaft, or barrel mount
Contains parts needed when installing the side shaft mount
Contains parts needed when installing the side shaft mount
July 2026GUID-9C83E43A-D15D-4D48-9AF6-AF0CBFA49D98 v3
Contains optional low-profile mounting screws
Contains optional longer screws for a shaft diameter greater than 42 mm (1.65 in.)
Contains an adapter disc needed when installing on a Force
®
Kraken trolling motor
Contains parts needed when installing the perspective mount
Contains an adapter disc needed when installing on the bottom shaft mount of a Spy Pole mount
Mounting Considerations
NOTICE
The use of third-party or self-fabricated mounts could lead to transducer damage or loss. Damage or loss
sustained when using a third-party or self-fabricated mount is not covered under warranty.
Using the hardware supplied, you can mount the transducer on a trolling motor or Spy Pole mount in the
following ways.
•Perspective Mount ()Installing the Transducer on the Perspective Mode Mount, page3
•You can mount the transducer on a trolling motor shaft using the perspective view bracket.
•You can use the transducer in perspective view, or rotate the bracket into the side shaft configuration to
use forward and downward views.
•Barrel Mount ()Installing the Transducer on a Trolling Motor Barrel, page7
•You can mount the transducer on either side of a trolling motor barrel.
•When mounted on a trolling motor barrel, you can use the transducer for downward and forward views.
•When mounted on a trolling motor barrel, you cannot use the transducer for perspective view.
•Bottom Mount
•You can mount the transducer to the bottom mount of a Force
®
Kraken trolling motor (Installing the
Transducer on the Force
®
Kraken LiveScope
™
Mounting BracketInstalling , page9) or a Spy Pole mount (
the Transducer on the Bottom Mount of a Spy Pole Mount, page11).
•When installed using the bottom mount method, you can use the transducer for forward, downward, and
perspective views.
When planning the installation, you should observe these considerations.
•You must angle the transducer correctly for the selected view to work properly.
•Installing the transducer with the included knobs allows for tool-free transitions between sonar views.
•You can use the included low-profile hardware instead of the knobs for a more permanent transducer view
position.
•You should mount the transducer in a location where it will not be jarred when launching, hauling, or storing.
Cable Considerations
NOTICE
Zip ties and cable clamps can over-tighten and damage or break the cable, or cause cable fatigue due to
repeated rotation of the motor.
You should use black electrical tape to secure the cable above and below a rotating joint. If you secure the cable
with zip ties, do not over-tighten the zip ties.
You should secure the cable above and below the pivot joint of a trolling motor.
The device cables have a minimum bend radius of 25 mm (9.8 in).
You should create a service loop at least 25cm (9.8in.) long in the cable, with the rotating joint centered on the
loop.
NOTICE
Failure to follow these considerations may void your product warranty.
You can extend the network cable using a Garmin BlueNet
™
coupler and extension cable from .buy.garmin.com
Routing the Transducer Cable
You should test-fit the transducer and cable before finalizing the installation.
2
LiveScope™ 2 Transducer
Installation Instructions
1Allow a loose gap of at least 20 cm (8 in.)
around the rotating joint
to
create a loop
in the cable.
The loop must be large enough to allow full rotation of the transducer
in both directions, so you can use a guideline of 10cm (4in.) above
and 10cm (4in.) below when establishing the loop. You should allow a
minimum of 25cm (9.8in.) of transducer cable to cover the 20cm (8in.)
section between the points where you secure the cable to the shaft.
2Use black electrical tape
to secure the transducer cable to the shaft.
3Test the full rotation of the trolling motor to ensure the cable clears the
rotating joint and is not pulled tight due to tension during rotation.
4Route the transducer cable through your vessel to the power source and
your chartplotter.
5Connect the included Y-split cable to the end of the transducer cable.
6Connect the positive (red) cable to the positive terminal on your power source, observing proper fusing.
7Connect the negative (black) cable to the negative terminal on your power source.
8
Connect the Garmin BlueNet
™
cable to your compatible chartplotter or network switch, using an adapter
cable if your chartplotter or switch has only a Legacy Garmin
®
Marine Network port.
Using the Optional Split Collar
If you plan to drill a hole or need to route the cable through a tight space during installation, you can remove the
existing solid locking collar on the cable before routing it. After routing the cable to the final location, you can
install the included split locking collar before making the connection.
1Use side-cutting pliers to cut through the existing solid collar.
Take care when cutting the existing collar to avoid damaging the cable or the connector.
2Remove the solid collar from the cable connector and save the existing o-ring if it is not damaged.
3Route the cable to the connection location.
4If needed, separate the two pieces of the optional split collar.
5Snap the pieces together around the cable connector.
6Insert either the original o-ring or the included replacement o-ring around the connector and into the collar.
Installing the Transducer on the Perspective Mode Mount
You can use the perspective mode mount to install the transducer in the perspective or side shaft configuration.
Labels identifying the parts bags required for this procedure:
NOTE: To avoid obstructions in the sonar image, you should mount the transducer on the shaft as far from the
motor as possible.
1Remove the perspective mode bracket from parts bag .
2Remove the adapter disc from parts bag , which is located within parts bag
.
3Remove the back half of the mounting bracket and four screws from parts bag .
NOTE: For a shaft diameter greater than 42 mm (1.65 in.), use the four screws from parts bag instead.
4Remove the knob from parts bag .
5If the trolling motor shaft is equal to or less than 25mm (1in.) in diameter, remove the rubber liner from
parts bag .
6Identify the arrow on the front half of the mounting bracket to ensure you install the bracket in the correct
orientation when you secure it to the trolling motor.
7If you are installing the transducer on a shaft equal to or less than 25mm (1in.) in diameter, wrap the
rubber liner
around the shaft at the location where you plan to install the bracket.
LiveScope™ 2 Transducer
Installation Instructions
3
Product specificaties
| Merk: | Garmin |
| Categorie: | Visvinder |
| Model: | LiveScope 2 LVS42HD |
Heb je hulp nodig?
Als je hulp nodig hebt met Garmin LiveScope 2 LVS42HD stel dan hieronder een vraag en andere gebruikers zullen je antwoorden