Garmin inReach Powered Mount Handleiding

Garmin Navigator inReach Powered Mount

Lees hieronder de 📖 handleiding in het Nederlandse voor Garmin inReach Powered Mount (19 pagina's) in de categorie Navigator. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/19
INREACH® POWERED MOUNT
Installation Instructions 2
Instructions d'installation 3
Istruzioni di installazione 5
Installationsanweisungen 7
Instrucciones de instalación 9
Instruções de instalação 11
Installatie-instructies 12
Installationsvejledning 13
Asennusohjeet 14
Installeringsinstruksjoner 15
Installationsinstruktioner 16
Instrukcja instalacji 17
Navodila za namestitev 18
Upute za instalaciju 19
Garmin®, the Garmin logo, and inReach® are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used without the express permission of
Garmin.
El número de registro COFETEL/IFETEL puede ser revisado en el manual a través de la siguiente página de internet.
December 2016 190-02165-92_0APrinted in Taiwan
INREACH® POWERED MOUNT
Installation Instructions
Important Safety Information
WARNING
See the guide in the Important Safety and Product Information
GPS device product box for product warnings and other
important information.
Installing the Device in the Mount
NOTICE
Before you place the device in the mount, ensure the metal
contacts on the device and the mount are dry. Moisture on the
contacts causes equipment damage. Use the weather cap to
keep the mount dry.
1Place the weather cap À
in the storage area on the mount.
2Align the mounting spine with the notches on the mount, and
slide the device down until it snaps into place.
Removing the Device from the Mount
1Press the tab À on the mount to release the device.
2Lift the device out of the mount.
3Place the weather cap on the metal contacts.
Connecting Power to the Mount
1Select a mounting location based on available power sources
and an unobstructed view of your surroundings.
2Route the USB cable, and connect it to a power source.
Attaching an AMPS Base Plate to the Mount
NOTE: The base plate is not included with all powered mounts.
1Thread the screws À through the washers Á, mount Â, and
base plate Ã.
2Tighten the nuts Ä to secure the base plate.
NOTE: The recommended torque is 1.7 to 2.25 N-m (15 to
20 lbf-in.).
Mounting the Device in an Automobile
1Clean and dry your windshield and the suction cup with a lint-
free cloth.
2Press the suction cup to the windshield, and flip the lever
À
clockwise.
3Align the ball of the suction cup mount and the ball of the
base plate Á with the double-socket arm Â.
4Tighten the knob Ã
slightly.
5If necessary, adjust for better viewing and operation.
6Tighten the knob to secure the mount.
2 Installation Instructions
SUPPORT DE MONTAGE INREACH®
AVEC ALIMENTATION
Instructions d'installation
Informations importantes relatives à la
sécurité
AVERTISSEMENT
Consultez le guide Informations importantes sur le produit et la
sécurité inclus dans l'emballage du GPS pour prendre
connaissance des avertissements et autres informations sur le
produit.
Installation de l'appareil sur le support
AVIS
Avant d'installer l'appareil dans le support, assurez-vous que le
support et les contacts métalliques de l'appareil sont secs. Vous
risquez d'endommager votre équipement si les contacts sont
mouillés. Utilisez le capuchon étanche pour protéger le socle de
l'humidité.
1Placez le capuchon étanche
À dans l'emplacement du
support prévu à cet effet.
2Alignez la rainure de fixation et la fente, puis faites glisser
l'appareil vers le bas jusqu'à ce qu'il soit bien en place.
Retrait de l'appareil du support
1Appuyez sur la languette
À située sur le support pour libérer
l'appareil.
2Soulevez l'appareil du support.
3Placez le capuchon étanche sur les contacts métalliques.
Raccordement du support à l'alimentation
1Choisissez un emplacement de montage en vous assurant
de disposer d'une source d'alimentation à proximité et d'une
vue dégagée.
2Acheminez le câble USB est branchez-le à une source
d'alimentation.
Fixation d'une base AMPS sur le support
REMARQUE : la plaquette de base n'est pas incluse avec tous
les supports de montage avec alimentation.
1Faites passer les vis À dans les rondelles Á, le support  et
la plaquette de base Ã.
2Serrez les écrous Ä pour fixer la base.
REMARQUE : il est recommandé de serrer les écrous selon
un couple de 1,7 à 2,25 N m (de 15 à 20 lbf/po).
Montage de l'appareil dans une automobile
1Nettoyez, puis séchez votre pare-brise et le support à
ventouse avec un chiffon non pelucheux.
Instructions d'installation 3


Product specificaties

Merk: Garmin
Categorie: Navigator
Model: inReach Powered Mount

Heb je hulp nodig?

Als je hulp nodig hebt met Garmin inReach Powered Mount stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Navigator Garmin

Handleiding Navigator

Nieuwste handleidingen voor Navigator