Fusion MS-CRGBWRC Handleiding

Bekijk gratis de handleiding van Fusion MS-CRGBWRC (12 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 72 mensen en kreeg gemiddeld 4.7 sterren uit 7 reviews. Heb je een vraag over Fusion MS-CRGBWRC of wil je andere gebruikers van dit product iets vragen? Stel een vraag

®

%+!&!,,     !’)-! )(-+)&

 ( ,-+.-%) ( ,

 ’*) +-( - "!-0  ( ") +’-%) (

    

Failure to follow these warnings and cautions could result in

personal injury, damage to the vessel, or poor product

performance.

See the guide in the Important Safety and Product Information

stereo box for product warnings and other important information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install

this product.

   

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

N OTIC E

When drilling or cutting, always check what is on the opposite

side of the surface to avoid damaging the vessel.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation,

contact Fusion® Product Support.

.**&%!,( ) )&,! ! !

•2-conductor 22 AWG (0.33 mm2) wire to connect the remote

control receiver to the power source

•6-conductor 22 AWG (0.33 mm2) wire (or equivalent

combination of 2- to 4-conductor wire) to connect the receiver

to the LED speakers

•Cable ties or adhesive for mounting the receiver

•4 gauge (3 mm) countersunk stainless-steel screws for

mounting the remote cradle (optional)

•3 mm flat screwdriver

•Wire cutters

•Drill and drill bits for mounting the remote cradle (optional)

).(-%(#(  )((! -%)()(,% !+-%) (,

When selecting a location for the remote control receiver and

making the wiring connections, observe these considerations.

•The receiver housing is not weather proof, and you must

install the receiver in a location that is not exposed to the

elements.

•You can connect a single receiver to up to 10 LED speakers

with RGB, cool white, and warm white functionality (5 pair).

You must use an additional receiver and remote control (sold

separately) to connect to additional LED speakers.

•You cannot use a single remote control with more than one

receiver.

) ( ( !-%( # -$! !’) -!) ( -+) & !!%/ !+

You can connect up to 10 (5 pair) of CRGBW LED speakers to

one remote control receiver.

 Route a power wire (not included) from a 12 Vdc power

source to the location of the receiver .

 Install the included 7.5 A fuse on the power wire.

 Route 6-conductor wire or equivalent (not included) from

the receiver to the speakers you want to control, joining the

wire where needed to connect up to 4 speakers.

 To avoid interference, you must not route the LED

wires near and parallel to any RCA, power, or speaker audio

cables. You should also avoid routing this cable near any

other electronic cabling on the vessel.

 Connect the 6-conductor wire or equivalent to the CRGBW

connectors on the speakers according to the installation

instructions provided with the speakers.

 Loosen the wire terminal screws on the bottom of the

receiver using a 3 mm flat screwdriver.

 Connect the power and RGB speaker wires to the wire

terminals on the sides of the receiver.

! --! +)(+! ! %/! +&! &%+! )&) +)+".(-%)(

INPUT +12V DC (left

side)

12 Vdc negative (-)

INPUT -12V DC (left

side)

12 Vdc positive (+)

V+ (BLACK) (right side)CRGBW 12 Vdc positive (+) (common)

wire

 Two V+ connectors are provided

on the right side for convenience. You

should connect the common wire from

the speakers to only one of these

connectors.

WARM WHITE

(YELLOW)

CRGBW warm white wire

COOL WHITE

(TURQUOISE)

CRGBW cool white wire

V+ (BLACK) (right side)CRGBW 12 Vdc positive (+) (common)

wire

 Two V+ connectors are provided

on the right side for convenience. You

should connect the common wire from

the speakers to only one of these

connectors.

REDCRGBW red wire

GREENCRGBW green wire

BLUECRGBW blue wire

 Tighten the wire terminal screws on the bottom of the

receiver.

 Secure the receiver to the mounting location using cable ties

or adhesive (not included).

(,-&&%(#-$!!’)-!) (-+) &+ &!

You can install the included remote cradle to store the remote

when not in use. Mounting hardware for the cradle is not

included.

N OTIC E

Because the remote control is not weatherproof, you must install

the cradle in a location that is not exposed to the elements.

 Using the cradle as a template, mark the two pilot holes.

 Remove the cradle from the mounting surface and drill the

pilot holes.

GUID-80736249-84A1-4457-B3FC-9231AA6112DC v1August 2020

Product specificaties