Fredenstein Bento 10 DS Handleiding
Fredenstein
Effect machine
Bento 10 DS
Lees hieronder de 📖 handleiding in het Nederlandse voor Fredenstein Bento 10 DS (9 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/9
Bento 10 DS
Module Carrier
Operating Manual
Fredenstein Bento 10 DS Module Carrier
The Fredenstein Bento 10 DS is the most advanced module carrier for ten Fredenstein Series 600
modules or API-500 compatible plug-in cards in 3U 19 inch rack-mount format. The Bento 10 DS
features several important upgrades compared with third party products:
the color LCD Display and a rotary encoder:
to set routing and other parameters with non-volatile storage. In addition, if certain Fredenstein
modules are used, like the F600A, F601A, F602, F603A/B, and the F607, all operating parameters
of theses modules are displayed as well.
Universal power supply:
accepting mains voltages from 90V AC to 240V AC, 50 to 60 Hz.
Increased output currents: 6A or 600 mA per slot and +48V DC 0.25A
Monitoring of output voltages and currents.
Auxiliary Audio Inputs and Outputs
Built-in Audio Routing:
Modules can be daisy-chained by simply using the menu driven user interface on the LCD.
Built-in compatibility switches for non-conforming modules.
Compressor buss linking:
Compressor modules can be linked simply using the menu driven user interface on the LCD as well.
Multi-layer back-plane:
Increased signal integrity and lower noise floor.
Ground-lift :
In case of ground loops, the audio ground and the protective ground can be disconnected. Please use
only if absolutely necessary.
Installation:
Electrical Safety Warnings:
Do not open the enclosure, hazardous voltages are present inside!
There are no user serviceable parts inside.
Always disconnect the mains cord before installing or removing modules!
If you need to replace the mains fuse, make sure the replacement has the same
rating ( 3.15 AT).
Please disconnect the mains from your Bento 10 DS before installing or removing modules. Make
sure each installed module is well seated in the receiving connector and the module is secured by
fasten the two mounting screws (size: M3).
Front View:
Fredenstein Bento 10 DS Manual V1.0 Sep 25, 2017 Page 1
Fredenstein Bento 10 DS Module Carrier
If certain non-Fredenstein modules are used, which bridge several pins on the connector and
connected the contacts on the top and button side, the double switches, located directly besides the
slot connectors, can both be turned off (lower position) to avoid interference between the module
and the digital interconnect. For Fredenstein modules, both need to be in the ON (upper) position.
To rack-mount the unit, the four feet have to be removed by their center screws.
Operation:
After installation of the modules, connect the mains cord to the Bento 10 DS IEC socket located on
the back-panel and than connect the mains cable to a grounded outlet. Now turn the Bento 10 DS on
by operating the I/O switch (also part of the IEC socket on the back). The following screen will be
displayed indicating the status and power-supply voltages and currents.
Now the Bento 10 DS is ready and will display any request from
certain Fredenstein modules. The Bento 10 DS will continuously
monitor the power-supplies and display the voltages and currents.
To enter the setup menu, please push the wheel and the setup menu
will appear.
Configuration of audio linking
Configuration of compressor buss linking
Various Setting
Save Configuration
Recall Configuration
Turning the wheel left or right to scroll from one menu point to the next, the highlighted menu point
will get selected when the wheel is pushed. Selecting Exit and pushing the wheel will show the
Status screen again.
Fredenstein Bento 10 DS Manual V1.0 Sep 25, 2017 Page 2
Product specificaties
| Merk: | Fredenstein |
| Categorie: | Effect machine |
| Model: | Bento 10 DS |
Heb je hulp nodig?
Als je hulp nodig hebt met Fredenstein Bento 10 DS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Effect machine Fredenstein
30 Januari 2023
Handleiding Effect machine
- Effect machine BeamZ
- Effect machine Behringer
- Effect machine HQ
- Effect machine HQ Power
- Effect machine Konig
- Effect machine Manta
- Effect machine Martin
- Effect machine Max
- Effect machine Midas
- Effect machine Monacor
- Effect machine Nedis
- Effect machine Pyle
- Effect machine Showtec
- Effect machine Velleman
- Effect machine Viking
- Effect machine JB Systems
- Effect machine Monoprice
- Effect machine NGS
- Effect machine Steren
- Effect machine Eurolite
- Effect machine American DJ
- Effect machine Antari
- Effect machine Chauvet
- Effect machine QTX
- Effect machine Karma
- Effect machine Adj
- Effect machine Elation
- Effect machine TC Electronic
- Effect machine Elysia
- Effect machine Stairville
- Effect machine Laserworld
- Effect machine TCM FX
- Effect machine Drawmer
- Effect machine ColorKey
- Effect machine Evo-Lite
- Effect machine Blizzard
- Effect machine Hazebase
- Effect machine IGS Audio
- Effect machine Cameo
- Effect machine Sagitter
- Effect machine DJPower
- Effect machine Doepfer
- Effect machine Fun Generation
- Effect machine Lotronic
- Effect machine IMG Stage Line
- Effect machine Lexicon
- Effect machine Futurelight
- Effect machine The Confetti Maker
- Effect machine BoomTone DJ
- Effect machine Klark Teknik
Nieuwste handleidingen voor Effect machine
26 Februari 2024
19 Februari 2024
19 Februari 2024
7 Februari 2024
7 Februari 2024
7 Februari 2024
7 Februari 2024
6 Februari 2024
6 Februari 2024
2 Februari 2024