Foscam FN7108HE Handleiding

Foscam Videorecorder FN7108HE

Lees hieronder de 📖 handleiding in het Nederlandse voor Foscam FN7108HE (3 pagina's) in de categorie Videorecorder. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

54 6 7

1 2 3

Quick Setup Guide

Network Video Recorder

Model: FN7108HE

V1.0.3

WARNING

Before installing a hard disk drive (HDD), please make sure the power

is disconnected from the NVR.

It is recommended that a hard drive be used in 7200 high-speed or

above.

Power cable

HDD

Data cable

It is recommended to use SATA type of hard disk for recording.

Note

1. Remove the cover from the NVR by unfastening the screws on the

rear and bottom.

2. Connect one end of the data cable and power cable to the

motherboard of NVR and the other end to the HDD.

3. Place the HDD on the bottom of the device and then fasten the

screws on the bottom to x the HDD.

4. Re-install the cover of the NVR and fasten screws.

HD-OUT Video Output

VGA Video Output

Procedure

1. Connect your display to one of the video outputs (VGA or HD-OUT

interface).

2. Connect an external storage device to the USB interface of the NVR as

a backup.

3. Connect a mouse to the USB interface.

4. Some devices need to connect to your router using an Ethernet cable,

including the NVR, PC and IP Camera.

5. Connect the power adapter to the power input port.

Foscam cameras and NVRs require good security practices to

safeguard your privacy. You should regularly change your

camera or NVR password which is the combination of

numbers, letters and symbols.

You should update your camera or NVR regularly. Make sure

your camera or NVR has the latest rmware installed for your

specic model and better experience.

Quick Setup Guide

Power Input Reset USB

USB

Power Switch Ethernet Port

IP Cameras Input Router Computer

Monitor

Mouse

NVR

Screw Pack

DC Power Adapter

Ethernet Cable

Data Wire and Power Wire

of the Hard Drives

Warranty Card

USB Mouse

1. Turn on the power switch on the rear panel.

After the NVR starts up successfully, the power LED and HDD LED

indicators will turn green. The startup page is displayed on the screen.

2. Login page.

Select the Language, Enter the and , then click Username Password

on the button.Login

Default username is

admin with no password

Package Contents

Security Warning

1 Before You Start 2 Hard Disk Installation

3. For the initial log in, the system will prompt you to change your

password. Once done, click the button. OK

4. After modifying the password, you will be taken to the Setup

Wizard.

1. Setting the time. If you don’t want to use the Setup Wizard next

time, uncheck the checkbox. Click the button.Setup Wizard Next

2. Select the HDD you would like to use, then click the Format Hard

Disk button to set up the HDD. Note that this will delete all les on

the HDD.

Select a protocol depending on which IP Camera you have.

FOSCAM protocol: The High Denition (HD) IP Cameras for Foscam.

MJ protocol: The Standard Denition (SD) IP Cameras for Foscam.

ONVIF protocol: IP Cameras which support ONVIF protocol.

3. You can add an IP Camera that is connected to the internet on the

NVR.

You can congure the following information for your IP Camera.

The Setup Wizard can walk you through some important settings on

the NVR.

1. Select Your IP Camera

2. Click Add

3 Device Connection 4 5 Log In Setup Wizard

Input a new password,

then click OK.

Uncheck the checkbox

2. Click Format Hard Disk

3. Click Next

1. Select your HDD

Format Hard Disk

For detailed manuals, tools, etc., please visit foscam.com/downloads.

8 9

12 13 14

1110

CE Certificate statement Website:

https://www.foscam.com/company/ce-certificate.html

Exporter and Importer Information Opened to Public:

https://www.foscam.com/company/open-information.html

www.foscam.com

As a result of product upgrades and other reasons, this guide may not be able to

update in time, resulting in inconsistency with the ocial website information,

please take the ocial website(www.foscam.com) information as the standard.

Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd

Addr: 9/F, Block F5, TCL International E City, No.1001

ZhongShanyuan Rd., NanShan District, Shenzhen, China, 518055

To disable recording, click again the button in the channel, or

uncheck the checkbox on the interface. channel Manual Record

Note

The maximum number of 4 playback video channels have been

reached, please deselect other channels rst to continue.

Note

This product supports 32-bit IE8 or later versions and does not

support 64-bit IE browsers. It also supports Apple Safari.

8.1 Network Conguration

8.3 Access to the NVR in WAN

Now you can access to your NVR using the DDNS address, such as

https://domain name:HTTPS port.

As an example: https://a6747.myfoscam.org:443

Click Add New...

If there is a UPnP function in your router.

Choose , make sure that the Forwarding > UPnP Current UPnP Status

is . Enabled

If UPnP has been in the router, you do not need to perform enabled

the following steps.

If UPnP is , you need to select one of the following methods disabled

to congure port forwarding on your router.

For these steps, we will be using the TP-LINK brand wireless router as

an example.

If there is no UPnP function in your router:

You need to manually add port forwarding, refer to the following

steps. You need go to the panel for Forwarding > Virtual Servers

setup.

Power Supply: DC 48V 2.0A 96W

You can also access the NVR or IP Camera directly through the local

network and remotely via manual port forwarding.

4. Repeat the step3 to add multiple IP Cameras. Find your IP Camera in

the , then click the button to complete the IP Camera List Finish

setup wizard.

After the IP Camera is added successfully to the NVR, there are two ways

to enable manual recording functionality when in the Live View mode.

Method 1

Left click the mouse in the channel, and some buttons will pop up as

shown . Click the button to enable recording.

You can see the recording information, include Manual Record, Alarm

Record, Schedule Record.

1. Right click the mouse in the Live View mode, and a shortcut menu

will pop up.

2. Select the to enter the page.Playback Playback

3. Select the time and Video Type of the recording. Check the Channels,

and you can check up to four channels.

4. Click the button. Then you can see the recording video in the Search

Playback page.

Method 2

1. Right click the mouse in the Live View mode, and a shortcut menu

will pop up.

2. Select the to enter the page.Manual Record Manual Record

3. Check the channels for which you want to enable recording. Click the

OK button.

4. Then click the icon to exit the interface.

In the Live View mode, the icon is at the bottom right of the screen

for each channel, indicating recording is on going.

1. Congure network information.

Right click the mouse in the Live View mode, choose Menu >

Settings > Network Network. Check the checkbox, then congure

the network information of the NVR.

It is highly recommended to set the port range from 5000 to 65535,

and the value of the port for each device should be unique.

2. Congure the DDNS.

Right click the mouse in the Live View mode, choose Menu > Settings

> Network DDNS. Check the checkbox. Enable DDNS on the NVR. We

recommend you to use the DDNS by default.

The live view interface will show you the video feed of each IP Camera.

If you have problems with your Foscam device, please contact the

Foscam reseller you purchased from, or you can e-mail the Foscam

headquarter technical support team: support@foscam.com

Your valuable comments and suggestions on improving Foscam

products are welcomed!

Select the Type

Check Network

Set the orHTTP Port HTTPS Port

IP Address: Set it to an IP address of

NVR in the range of the router

address pool, or keep it as default.

Subnet Mask: Keep it as default.

Gateway: Should be the same as the

Router’s IP address.

DNS Server: Should be the same as

the router’s DNS Server address.

Check UPNP Click Save

8.2 Access to the NVR in LAN

Double click the NVR in the list, and your default browser will open up

to the login page.

You can access to the NVR via the browser in LAN.

Manual Recording

Playback

8 Remote Access

10 Technical Support

Click Save

Check DDNS

Check Enable DDNS

Download the “Equipment Search Tool” from

foscam.com/tools to your computer. Run it, and it will display

information of the NVR on your LAN.

9 Product Performance

Input the port and IP address

of your NVR and click . Save

443

7. Click OK

3. Select the Channel

5. Input the and Username

Password of the IP Camera .

4. Enusre that the IP address of the

IP Camera and NVR is on the same

network IP segment, and that the

subnet mask and gateway are the

same as the NVR's.

Click Finish

6. Select the protocol.

Product specificaties

Merk:	Foscam
Categorie:	Videorecorder
Model:	FN7108HE
Ondersteunde mobiele besturingssystemen:	Android, iOS
Aan/uitschakelaar:	Ja
Video-opname modi:	1080p
Maximum resolutie:	1920 x 1080 Pixels
Video bewegings-detectie:	Ja
Inclusief AC-adapter:	Ja
Aantal USB 2.0-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	1
Ondersteunt Windows:	Ja
Aantal poorten USB 3.2 Gen 1 (3.1 Gen 1) Type A:	1
Mac-compatibiliteit:	Ja
Reset button:	Ja
Snelle installatiehandleiding:	Ja
HDD capaciteit:	- GB
Power over Ethernet (PoE):	Ja
Ondersteunde browser:	Internet explorer, Safari
Maximale opslagcapaciteit:	4 TB
VGA (D-Sub) uitgang ports:	1
Videoingangkanalen:	8 kanalen