Focal Polyglass 165 V30 Handleiding

Focal Speaker Polyglass 165 V30

Lees hieronder de 📖 handleiding in het Nederlandse voor Focal Polyglass 165 V30 (16 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16
polyglass 165 V 30
U s e r M a n u a l
Congratulations on choosing Focal automobile speakers.
Focal speakers remain high quality products, due to the multitude of advanced
materials used. Detailed research and development in the laboratory, from
dedicated engineers and technicians, played a major role in producing such high
performing products. To gain the best results from your speakers, please ensure
you follow these recommendations. If not followed correctly any fault observed,
may not be covered by the guarantee.
Français page 6
the focal only guarantee applies if is page 15
ret urned to us wi th i n 10 days o f purcha se .
Technical advances, included in the Polyglass range
• Polyglass cones woofer
• TNB aluminum / magnesium inverted dome tweeter
• Separated crossover, fully optimised with adjustable level control. High quality components
used throughout.
• Butyl surround
Included
• 2 x midbass drivers
• 2 x grilles with support
• 2 x gaskets
• 2 x tweeters with grilles
• 2 x tweeter supports
• 2 x crossovers
• Fixing screws
Due to constant technological advances, Focal reserves its right to modify specifications without notice. Images may not conform exactly to specific product.
Focal® is a trademark of Focal-JMlab® - BP 374 - 108, rue de l'Avenir - 42353 La Talaudière
cedex - France - Tel. (+33) 04 77 43 57 00 - Fax (+33) 04 77 43 57 04 - www.focal-fr.com
Important recommendations
Before attempting any installation work, it is very important to verify how much space is
available to fit the speakers into the vehicle.
Key points:
• For direct replacement of original speakers, please check there is enough space for your
new Focal speakers and grilles.
• Ensure the speaker is clean from debris and metallic particles that maybe attached
(especially after drilling)
• Use the foam gasket supplied (inside the grille), for airtight placement of the speaker into
the panel.
• Do not touch the tweeter cone.
Choice of installation and positioning the tweeter
To achieve best results for your installation, please follow these simple guidelines
• Use a variety of speakers to achieve a large bandwidth, the most central possible.
• Speakers positioned in the most forward location possible, for correct staging.
• Tweeters positioned preferably high in the doors or in the dash (if space permitting),
to obtain un-muddled high and midrange frequencies. These being directive to the
listener.
• To position the tweeters direct in-line to the listeners ears, for improved imaging.
Prefered woofer and
mid-range positions.
3 x prefered tweeter
positions
polygl a ss 165 V 30
U s e r M a n u a l 2
Cables and connections
For best results with your speakers, we recommend you include the use of Focal cables.
Alternatively, other high quality cable can be used, if sufficient section thickness is available
(minimum thickness = 1mm2). This is particularly important for long lengths of cable to
ensure a strong efficient signal is maintained. Always ensure the polarity is respected, (+ is
connected to + and - is connected to -). Maintain correct connections, from principal source
radio / amplifier (left / right / front and rear), and crossover to speakers (tweeter to tweeter, mid
to mid, woofer to woofer), is always observed.
Connections
Fitting the tweeter
There are two mounting possibilities available: surface or flush mount. The tweeter arrives
supplied in its flush-mounting pod. Very carefully, remove the grille, by gently prizing it off
(using a paper clip will help). Don’t forget to put the grille back, it has a great impact on the
tweeter frequency response.
Surface mounting: choose the angle that best suits your installation (10° or 30°) and mount
the pod firmly using the screws supplied. Feed the wire through the hole in the pod and refit
the tweeter and grille in place.
Flush mounting: cut a neat 45mm diameter hole
in the panel where you want to place the tweeter.
Then with the metal mounting strip held from
behind (ensuring the ends are pointing towards
the hole), insert the screw through the flush-mount
pod from the front and tighten the two parts
together. Feed the wire through the hole in the pod
and refit the tweeter and grille in place.
polyglass 165 V 30
U s e r M a n u a l 3
Right Output
Left Output
Woofer
Tweeter
Woofer
Tweeter
Input
Input
Grille
Unlocking tool
Tweeter
Pod
Mounting strip

Product specificaties

Merk: Focal
Categorie: Speaker
Model: Polyglass 165 V30

Heb je hulp nodig?

Als je hulp nodig hebt met Focal Polyglass 165 V30 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker Focal

Focal

Focal Twin6 Handleiding

17 April 2024
Focal

Focal Aria Evo X N°1 Handleiding

26 Maart 2024
Focal

Focal Sopra N°2 Handleiding

26 Maart 2024
Focal

Focal IFR 165-2 Handleiding

15 Maart 2024
Focal

Focal ES 165 K2S Handleiding

8 December 2023
Focal

Focal ES 165 KE Handleiding

8 December 2023
Focal

Focal ES 100 KE Handleiding

8 December 2023
Focal

Focal ES 165 KX2E Handleiding

8 December 2023
Focal

Focal ES 165 K2E Handleiding

8 December 2023
Focal

Focal ES 165 KX3E Handleiding

8 December 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

OTTO

OTTO Bluetooth Revo NC2 Handleiding

20 April 2024
REL Acoustics

REL Acoustics Strata Handleiding

20 April 2024
REL Acoustics

REL Acoustics Strata III Handleiding

20 April 2024
Soen

Soen Transit Handleiding

18 April 2024
Miller & Kreisel

Miller & Kreisel MP300RC Handleiding

18 April 2024
Soen

Soen Transit XS Handleiding

18 April 2024
Miller & Kreisel

Miller & Kreisel MP7 Handleiding

18 April 2024
Qian

Qian QRBT1801 Handleiding

17 April 2024
Kenwood

Kenwood KFC-WPS1000F Handleiding

16 April 2024
Yamaha

Yamaha NS-IW660 Handleiding

16 April 2024