Focal FDP 4.600 Handleiding

Focal Receiver FDP 4.600

Lees hieronder de 📖 handleiding in het Nederlandse voor Focal FDP 4.600 (8 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
1
POWER PER CHANNEL:
• 4 x 150 wRMS @ 4ohms
• 4 x 200 wRMS @ 2ohms
• 2 x 400 wRMS (Bridged @ 4ohms)
ROUTE SWITCH
• 1+2 = All four RCA inputs are used.
• 3+4 = Input signal on channels 3+4 are routed to channels 1+2. Use this mode when you need a band pass filter
on all four channels.
Recommended when bridging channels 1, 2, 3, 4.
The level controls still function.
• Copy = Input signal and filters on channels 3+4 are copied to channels 1+2. Use this mode when you need a band
pass lter on all four channels.
Recommended when bridging channels 1,2,3,4.
The level controls still function.
CHANNELS 1 & 2 CROSSOVER CONFIGURATION
• Flat: Full Range Signal. No crossover filter used.
• HP: Activates the High Pass Filter for a midbass or tweeter.
CHANNELS 3 & 4 CROSSOVER CONFIGURATION
• Flat: Full Range Signal. No crossover filter used.
• HP: Activates the High Pass filter.
• LP/BP: Activates the selection of either a Low Pass filter for woofer or a Band Pass filter for midrange.
• MONO Mode: Inputs 3+4 are mixed to mono for bridge mode operation. If 1+2 ROUTE is set to COPY then 1+2
will also be mono subwoofer and the remote volume control will control level.
The subwoofer remote volume control is activated. There is a clip distortion light on the remote volume control.
If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.
AUTOMATIC POWER TURN ON/OFF
1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio
connected to the REM amplifier terminal.Band Pass for a subwoofer or midbass of a 3 way speaker.
2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn
on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not
necessary.
FDP 4.600 : FOUR CHANNEL AMPLIFIER
Operation / Configuration
2
RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL.
• The amplifier control has sufficient adjustment range for both low level and high level input into the RCA LEVEL
jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers,
can be directly connected to the RCA jacks when the amplifier control is adjusted to 8V.LEVEL
SETTING LEVEL
• Set the amplifier control to minimum before you turn on the amplifier for the first time.LEVEL
• For lowest distortion and lowest noise the amplifier should be set at the lowest setting that yields LEVEL
sufcient loudness without distortion. For lowest noise your source radio volume control should be near
maximum that does not cause distortion.
• To find the best amplifier setting: LEVEL
With the amplier at minimum, slowly increase the source radio volume to around 3/4 without distortion. LEVEL
Then, slowly turn up the amplier control to the maximum desired loudness. Listen very carefully and LEVEL
turn down the amplier control if you hear any distortion.LEVEL
FPD 600.4 CONFIGURATION EXAMPLES
4 CHANNEL STEREO NON-BRIDGED
• (SEE GRAPHIC B1)
• If you have four input wires from the source deck, plug them into inputs 1+2 and 3+4.
Set ROUTE switch to 1+2.
• If you have two input wires from the source deck, plug them into inputs 3+4.
Set ROUTE switch to 3+4.
Set the switch to STEREO.
• If you are NOT using a subwoofer set all switches to flat. If you hear distortion in your woofers set all switch to
HP and adjust all HP frequency until the distortion goes away, this will probably be around 50 Hz to 70 Hz.
RADIO FLAT or HP50Hz
1+250Hz FLAT or HP
STEREO
B1
XOVER
XOVER XOVER
XOVER
B1 <GRAPHIC of Source Radio to input channel 1+2, 3+4 of amplier. Woofer/Tweeter/Xover on channels 1+2, 3+4>
3
IF YOU ARE USING TWO SUBWOOFERS:
• (SEE GRAPHIC B2)
• Put your woofer/tweeters on channel 1+2.
Set 1+2 switch to HP.
Adjust 1+2 HP frequency to 50 Hz.
• Subwoofers on channel 3+4.
Set 3+4 switch to LP/BP.
Set 3+4 switch to LP.
Adjust 3+4 LP frequency to 50 Hz.
Set the switch to MONO.
Plug in the remote sub control.
RADIO LP LP/BP50Hz
3+450Hz HP
MONO
B2
+ –
SUBWOOFER
+ –
SUBWOOFER
REMOTE SUB CONTROL
XOVER
XOVER
B2 <GRAPHIC of Source Radio to input channel 3+4 of amplier. Woofer/Tweeter/Xover on channels 1+2, one


Product specificaties

Merk: Focal
Categorie: Receiver
Model: FDP 4.600

Heb je hulp nodig?

Als je hulp nodig hebt met Focal FDP 4.600 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Focal

Handleiding Receiver

Nieuwste handleidingen voor Receiver