Fito ASD-10 Handleiding

Fito Rookmelder ASD-10

Lees hieronder de 📖 handleiding in het Nederlandse voor Fito ASD-10 (2 pagina's) in de categorie Rookmelder. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

IMPORTANT INFORMATION

Correct usage will ensure you have valuable extra time to

escape. Every correctly installed smoke detector will

increase your potential escape time.

• measure.A smoke detector is not a fire-prevention

• pos-sible Install the smoke detector in the correct place, if

in the middle of the ceiling.

• children.Keep the smoke detector out of the reach of

• period of Test the unit on a weekly basis and after any

absence.

CAUTION: Never test with fire!

• Clean the detector regularly (once a month) using the soft

brush from a vacuum cleaner. The smoke alarm can also

be cleaned using a moist cloth.

• If the detector emits a beeping sound every 40 seconds,

this means that the battery is nearly flat and that you should

replace the smoke detector.

• years.The lifespan of smoke detectors is 10

• and A false alarm can be silenced by pressing the test

silence button.

• You can make your Model ASD-10 smoke detector less

sensitive for 8-9 minutes by pressing the test but-ton. The

detector will nonetheless sound the alarm if the quantity of

smoke is too significant.

• Plan TWO escape routes and rehearse these with all

members of the family.

• BUILDINGIN THE EVENT OF A FIRE: LEAVE THE

IMMEDIATELY TAKING ALL FAMILY MEMBERS

WITH YOU, GATHER OUTSIDE AT A PRE-AGREED

MUSTER POINT AND CHECK THAT EVERYONE IS

PRESENT AND ACCOUNTED FOR.

CLOSE ALL AND DOORS BEHIND YOU NEVER

OPEN A WARM DOOR. IF A DOOR IS WARM,

CHOOSE AN ALTERNATIVE THE ROUTE. CALL FIRE

BRIGADE OUTSIDE AT A FROM OR NEIGHBOUR’S

HOUSE. NEVER GO BACK INTO A BURNING

BUILDING.

• In the event of considerable build-up of smoke, crawl out of

the building keeping as close to the floor as possible.

Wherever possible, breathe through a cloth (preferably

moist), or else hold your breath as much as you can. The

majority of deaths and injuries are caused by smoke

inhalation rather than fire itself.

SPECIFICATIONS

Power: Battery3VDC Lithium AA

Battery 10 years under life: normal

conditions

Usage: < 10 µA continuous

< 60 mA in alarm

Usage temperature: 0ºC to + 55ºC

± 3% at 93% RH at 40ºCHumidity:

Sensitivity:

Alarm volume:

Certification:

In accordance with EN14604

>85dB at 3 metres

ANPI EN14604, CE-13, BOSEC

POSITIONING THE SMOKE DETECTOR

Minimum protection:

In all rooms, such as bedrooms, living room, study and

suchlike, as well as along escape routes such as corridor

or hallway.

Maximum protection:

- Smoke detector in all rooms (with the exception of

bathrooms, kitchen, garages, etc.)

- Heat detectors can be installed in bathrooms, kit-

chens, airing cupboards, utility rooms, etc. within 5

metres of a potential source of fire.

Recommended

locations:

• smokeThe

detector should

preferably be

installed in the

middle of the

ceiling, at least

50 cm from the

wall.

• ofIn the case

pitched roofs,

install the detec-

landing

tor on the slo-

ping wall, at

least 90 cm (measured vertically) from the ridge of

the roof.

• See minimum and maximum protection (figures 1 & 2)

• Ensure that the detector can always be reached

for testing and cleaning.

Never fit a smoke detector:

• In bathrooms, kitchens, shower rooms, garages, etc.

Places where a smoke detector may go off needles-

sly due to condensation, normal smoke or gases. A

smoke detector should be fitted at least 5 metres from

such sources of smoke.

• 50° Places where the temperature may exceed C

or fall 0° below C, e.g. attics, just above a fireplace,

•In the vicinity of (or adjacent etc. to) decorative objects,

doors, sockets, lights, fittings, windows, wall venti-

lators, etc. which could mean that smoke does not

reach the smoke detector. Minimum 50cm away.

• Surfaces that are usually warmer or colder than the

rest of the room. Differences in temperature can pre-

vent smoke from reaching the detector.

• heaters.Adjacent to or directly above stoves or

figure 4

LED-light

test-/pause button

figure 1

kitchen

living room

bath-

room

bedroom

hallway

bedroom

bedroom hallway

kitchen living

room

figure 2

hallway

Instruction manual

10-YEAR OPTICAL SMOKE DETECTOR WITH BUILT-IN 10-YEAR 3V BATTERY

1134

EN14604:2005/AC 2008

Essential characteristics: Performance:

Nominal activation conditions/sensitivity,

response delay (response time) and

performance under fire conditions:

Passed

Fito Products BV

Molenvliet 22

3961 MV

Wijk bij Duurstede

The Netherlands

1134-CPR-122

Operational reliability: Passed

Tolerance to supply voltage: Passed

Durability of operational reliability and

response delay, temperature resistance:

Passed

Durability of operational reliability,

vibration resistance:

Passed

Optical smoke

detector, alerts you in

the event of fire or

smoke, and is suitable

for esidential r

buildings.

Durability of operational reliability,

humidity resistance:

Passed

Durability of operational reliability,

corrosion resistance:

Passed

Durability of operational reliability,

electrical stability:

Passed

9178

RETAIN THESE INSTRUCTIONS FOR USE!

These instructions for use contain important information for correct installation and

use of your smoke detector. Please read this information carefully and retain these

instructions for reference.

Model: ASD-10

• it hard In very high or difficult to reach places. This makes

to reach the detector to test or clean it.

• In very dusty or dirty places. Accumulation of dust will

prevent smoke from reaching the smoke chamber and in

time will lead to a false alarm.

• Some Within 1 metre of dimmer switches and wiring.

dimmer switches can trigger a fault in the detector.

• Within 1.5 metres of fluorescent lights. Electrical impulses

can adversely affect the functioning of the detector.

• Outdoors and in spaces where a large number of insects

are found. Small insects in the unit’s detection chamber can

disrupt the functioning of the detector.

The underside of the detector gives important

information.

ATTENTION: The smoke alarm should be temporarily

removed during renovation work or structural alterati-ons.

Clean the smoke detector with the soft brush from a vacuum

cleaner once the day’s work is complete, and then replace

the detector, always testing it by pressing the test button

once it has been reinstalled.

INSTALLATION

1. Choose location a that

satisfies the conditions as

described in: Positioning

the smoke detector .

2. Remove the base plate

of the detector (figure

3) baseby turning the

plate anticlockwise (to

the left).

3. mounting Mark the

figure 3

holes in the base plate

and drill the holes (use a 6 mm drill). If not using the

screw plugs, then use a 3 mm drill. Screw the base

plate securely onto the ceiling. Make sure that the base

plate is tight against the ceiling so that no air circulation

above the smoke alarm is possible, which could impede

smoke detection. If the opening is too large, this should

be remedied using the kit.

4. Place the smoke detector on the base plate and turn it until

the smoke detector clicks into the base plate. Turn the

smoke detector clockwise (to the right from the OFF to the

ON stripe) to secure the smoke detector and activate it. (See

figure 4)

Mounting holes

PRODUCT WARRANTY

If used and maintained properly, the manufacturer gua-

rantees this product against material and/or manufacturing

faults for a period of 10 years from the original date of pur-

chase by the consumer. Exceptions include damage arising

from accidents or misuse. If the product becomes defective

within the stated period, then it will be repaired or replaced

free of charge. Please do not attempt to repair the product

yourself or tinker with it, which will invalidate the warranty.

MADE IN EUROPE

EUROPEAN SUPPLIER:

Fito Products BV

Molenvliet 22

3961 MV WIJK BIJ DUURSTEDE

The Netherlands

info@fito.nl - www.fito.eu

5. Check that the smoke detector is working and that the

battery has been activated by pressing the test button. A

beeping noise that stops of its own accord indicates that the

smoke detector has been activated and the red LED light will

flash every 10 seconds for 8-9 minutes. Testing the smoke

detector will automatically put it in reduced sensitivity

mode for 8-9 minutes.

• Never allow the detector to come into contact with fluids.

• Clean the detector regularly (once a month) using the soft

brush from a vacuum cleaner. The smoke alarm can also

be cleaned using a moist cloth.

• manufacturer.Repairs must be carried out by the

CAUTION: Never apply paint to the detector and do

not cover it in tape.

Causes of false alarm:

The smoke detector can be activated by steam, condensa-

tion, dust, smoke and small insects. These are to be preven-

ted as far as possible. See section: Never fit a smoke detec-

tor. If a detector is frequently giving a false alarm, it might be

necessary to install the detector in another location.

INSTRUCTIONS FOR REMOVAL

Do not dispose of your old detector in the

bin, but rather hand it in to a local

collection point for small, domestic waste.

LIMITATIONS OF SMOKE DETEC TORS

In countries where they are commonly in use, smoke

detectors have contributed to reducing deaths and injuries.

Independent bodies have established that they were insuf-

ficient in around 35% of fires, namely in the following

situations:

• working. Where the battery had been removed or was not

For that reason, you should test the unit regularly.

• Where smoke is not able to reach the detector in the event

of a fire, meaning the unit cannot be set off. Examples

include a fire on another floor where there is no smoke

detector, a fire behind closed doors, a fire in a chimney or

smoke being blown away from the detector. For that

reason, smoke detectors are recommended in all rooms, or

at any rate on every floor.

• Where the alarm is not heard. A person may not be woken

by the alarm if that person had consumed excess alcohol

and/or drugs.

• A few fires are not always detected on time, e.g. smoking in

bed, if there is no smoke detector in the bedroom. In the

case of escaping from gas or violent explosions,

improperly storing explosive products and flammable liquids

(petrol, paint, methylated spirit, etc.), electrical faults,

acids, children playing with matches (fire).

• years.The lifespan of smoke detectors is 10

DECLARATION OF PERFORMANCE

You can cownload the Declaration of Performance on our

website www.fito.eu.

2015-04

FUNCTION AND MEANING OF THE LIGHT AND SOUND

SIGNALS:

Normal situation: The will flash once red LED light every 5

minutes.

Alarm: Whenever detects smoke, will emit the detector it a

loud pulsing alarm and the red LED light flash will continu-

ously until the smoke has cleared.

Low battery signal: A signal every beeping 40 seconds

means that the is flat the battery nearly and smoke detector

needs to be This signal will sound for 30 replaced. days.

When properly maintained, as described under IMPORTANT

INFORMATION, battery and the alarm the smoke should

continue to work a before reaching the for over decade end of

their lifespan. You remove the smoke should detector and

base the a plate from ceiling and install new smoke

detector.

Test and Pause Button: Your fitted detector is with a

pause (see figure is the button as button 4). This same the

test button. the pause/test button Press for 2-3 seconds.

Your smoke will go into detector then a so-called reduced

sensitivity minutes. LED mode for 8-9 The red light will flash

every seconds silence 10 to the indicate that button has

been activated. The will sound detector nonetheless the

alarm if the smoke dense or increasing in is quantity. False

Alarm: Press the button to stop the alarm. test (See Test

and Pause button)

Light sensitivity: Three short beeps every 40 seconds, means

the smoke alarm is exposed to too much light

(light spot or sun). Move the smoke detector, or remove the light

source.

Maintenance:

Product specificaties

Merk:	Fito
Categorie:	Rookmelder
Model:	ASD-10

Heb je hulp nodig?

Als je hulp nodig hebt met Fito ASD-10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Rookmelder Fito

Fito HA-163 Handleiding

17 Juni 2023

Fito SND-500-S Handleiding

17 Juni 2023

Fito GS-402 Handleiding

17 Juni 2023

Fito GS-506 Handleiding

17 Juni 2023

Fito FIT-128C Handleiding

17 Juni 2023

Fito GS-505 Handleiding

17 Juni 2023

Fito GS-3000 Handleiding

17 Juni 2023

Fito ASD-10QR Handleiding

14 April 2023

Fito ASD-10Q Handleiding

17 Maart 2023

Fito ASD-10 Handleiding

25 Februari 2023

Handleiding Rookmelder

Nieuwste handleidingen voor Rookmelder

First Alert SA320 Handleiding

9 April 2024

Nexa MSA-866 Handleiding

25 Maart 2024

Nexa WSA-102 Handleiding

25 Maart 2024

EMOS P56500S Handleiding

13 Maart 2024

Cordes CC-5/evo10 Handleiding

12 Maart 2024

FireAngel HW10 Handleiding

12 Maart 2024

GEV FMR 4023 FlammEx Handleiding

5 Maart 2024

GEV FMR 3286 FlammEx Handleiding

5 Maart 2024

GEV FMR 4467 Handleiding

5 Maart 2024

GEV FMR 3569 FlammEx Handleiding

5 Maart 2024