Festo PFML-90-HP3 Handleiding

Bekijk gratis de handleiding van Festo PFML-90-HP3 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.2 sterren uit 5 reviews. Heb je een vraag over Festo PFML-90-HP3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Micro filter

PFML-90

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Operating instructions

Translation of the original instructions

8081782

2017-10b

[8081784]

For all available product documentation è www.festo.com/pk

Micro filter PFMLEnglish..............................................

1Configuration

1

2

3

4

5

6

7

8

9

aJ

aA

aB

1Spanner flat for loosening and

attaching the filter bowl

2Filter bowl

3O-ring to seal the filter bowl

4Filter cartridge

5Compressed air supply port 1

(inlet)

6Slots for mounting the module

connectors

7Alternative compressed air supply

port 1 (inlet)

8Compressed air supply port 2

(output)

9Front cover

aJPneumatic connection x" (p2) for

differential pressure sensor – [22]

aAPneumatic connection x" (p1) for

differential pressure sensor – [11]

aAConnection G½ for condensate

drain

Fig. 1

Note

The micro filter PFML-90-HP3-... can be retrofitted with a fully automatic conden

sate drain and a differential pressure sensor.

–It is possible to drain the condensate manually or retrofit a fully automatic

condensate drain at the connection G½ aB.

–Connections Gx are present on the front and rear side to retrofit a differential

pressure sensor for pressure sensing.

–Blanking plugs and the matching sealing rings for sealing the connections Gx

and G½ are included in the scope of delivery.

–Press-on front cover is not included in the scope of delivery.

2Application

The micro filter PFML-90-HP3 is intended exclusively to remove dirt particles and

oil drops from the compressed air supplied.

The product may only be used in its original status without unauthorised modi

fications. Only the assembly and commissioning activities described in these

operating instructions are permissible.

Observe the permissible limit values and specifications (è Technical data).

Only use the product if it is in an excellent technical status.

Only use pre-filtered compressed air as an operating medium in accordance with

the specification (è Technical data).

Operation with fluids or gases is impermissible.

Use the filters only in the marked flow direction.

Take into consideration the legal regulations applicable for the location as well as:

–Regulations and standards,

–Regulations of the testing organisations and insurers,

–National specifications.

3Installation

Note

Installation should only be conducted by qualified personnel.

Connecting plates of the type PAML-CP are required for direct mounting of an

individual device.

Module connectors of type PAML-MK are needed for linking individual devices

to a service unit.

Information on mounting of module connectors, connecting plate and mounting

brackets can be found in the documentation enclosed with the accessories.

aC

aD

Fig. 2

1.Check the system conditions on site before installation:

–The piping system is unpressurized and no medium flows in it.

–The supply lines are clean and free of wear-causing particles.

–The alternative pressure supply port is tightly plugged and sealed with

a blanking plug and related sealant (not contained in scope of delivery).

–The connections for differential pressure sensor aJaA, and condensate drain

aB are tightly plugged and sealed (Blanking plugs and the related sealing

rings are included in the scope of delivery).

–The filter bowl 2 is firmly tightened on the housing.

–Shut-off valves for venting the system are mounted in the compressed air

supply line.

2.Put the filter in its mounting position.

–Observe the flow direction. The numerals 1 (inlet side) and 2 (outlet side) on

the product housing serve as orientation (è Fig. 1).

–Comply with the minimum distance beneath the filter bowl of 210 mm.

–Align vertically standing with filter bowl below (vertical ±5°).

3.Push the module connector aC into the grooves of the filter and of the adjacent

individual device.

4.Connect the filter with the adjacent individual device.

–Place the supplied seal aD at the connection point.

–Push the filter and adjacent individual device together and mount the module

connector.

5.Assemble the service unit and connect it to the compressed air line.

When using the alternative compressed air supply port 7

Screw the connector into the pneumatic connection using a suitable sealant.

–Connection size 1".

–Screw-in depth 18 mm.

Securely seal the compressed air supply port 5. Use a connecting plate

PAML-CP (è Accessories) and appropriate blanking screws and sealant.

4Commissioning

Note

Commissioning should only be conducted by qualified personnel.

Observe the specifications on the rating plate.

Place the micro filter in operation only when it is completely assembled and

installed.

Check the connection points for tightness.

Product specificaties