Festo DADP-SP-G9-20-R Handleiding

Bekijk gratis de handleiding van Festo DADP-SP-G9-20-R (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 58 mensen en kreeg gemiddeld 4.9 sterren uit 5 reviews. Heb je een vraag over Festo DADP-SP-G9-20-R of wil je andere gebruikers van dit product iets vragen? Stel een vraag

DADP-SP-G9-...-R

Sub-base kit

Festo SE & Co. KG

Ruiter Straße 82

73734 Esslingen

Germany

+49 711 347-0

www.festo.com

Assembly instructions

8195137

2023-07a

[8195139]

8195137

Translation of the original instructions

© 2023 all rights reserved to Festo SE & Co. KG

1

Applicable documents

All available documents for the product

è

www.festo.com/sp.

DocumentProductContents

Operating instructionMini slide DGSS–

Operating instructionShock absorber DYEF, DYSS–

Tab. 1:

Applicable documents

2Safety

2.1

Safety instructions

–Only mount the product on components that are in a condition to be safely

operated.

2.2Intended use

The sub-base kit in combination with two shock absorbers on the mini slide DGSS

cushions its extended and retracted end position. The sub-base contains the axial

air connections for the mini slide.

3

Additional information

–Contact the regional Festo contact if you have technical problems

è

www.festo.com.

–Accessories

è

www.festo.com/catalogue.

4

Product Range Overview

4.1Scope of delivery

1

2

35674

Fig.1

1

Screw (2x)

2

Stop (1x)

3

Stop element (1x)

4

Screw (2x)

5

O-ring (2x)

6

Connecting plate (1x)

7

Screw (4x)

4.2

Not in scope of delivery

8

9

Fig.2

8

Mini slide (1x)

DGSS

9

Shock absorber (2x)

DYEF-G8/DYSS-G8

5Product design

Z

Z

Y

Fig. 3:Product design

Y

Axial air connections

Z

Thread for shock absorber

6Assembly

1

A

B

2

Fig. 4:Pushing in stop

1.Extend the slide[A] manually.

2.Slide the stop into the slot[B].2

3.

Insert the screws into the holes of the stop.12

4.

Slide the stop to the end of the slot[B].2

A

C

1

Fig. 5:

Mounting stop

1.

Position the slide[A] so hole[C] is aligned with a screw.1

2.

Tighten the screw. Observe the tightening torque.1

DADP-SP-G9-6-10-16-20

ScrewM2 x 6M2.5 x 8M2.5 x 8M3 x 12

[Nm]0.3 ±15%0.5 ±15%0.7 ±15%0.9 ±15%

3.

Repeat this process for the second screw.1

C

3

Fig. 6:

Note the stop bar

•When installing the stop element, note the position of the stop bar[C].3

3

D

A

Fig. 7:

Aligning stop element

1.Retract the slide[A] manually.

2.

Position the upper edge of the stop element at the level of the thread[D].3

3

A

C

Fig. 8:

Attaching stop bar

1.Push the stop element upwards to the stop.3

Ä

The stop bar[C] is in contact with the slide[A].

2.Hold this position.

Product specificaties