Fellowes Powershred 64Cb Handleiding

Fellowes Papiervernietiger Powershred 64Cb

Lees hieronder de 📖 handleiding in het Nederlandse voor Fellowes Powershred 64Cb (8 pagina's) in de categorie Papiervernietiger. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

Quality Office Products Since 1917

POWERSHRED® 64Cb

Please read these instructions before use.

Do not discard: keep for future reference.

Veuillez lire ces instructions avant d’utiliser l’appareil.

Ne pas jeter : conserver aﬁn de consulter les directives

ultérieurement, en cas de besoin.

Lea estas instrucciones antes del uso.

No las deseche: consérvelas como referencia futura.

CAPABILITIES

ENGLISH

Model 64Cb

Will shred: Paper, credit cards, staples and small paper clips

Will not shred: Adhesive labels, CD/DVDs, continuous form paper, transparencies,

newspaper, cardboard, large paper clips, laminates, file folders, X-rays or plastic other than

noted above

Paper shred size:

Cross-Cut .......................................................................... 5/32 in. x 2 in. (4mm x 50mm)

Maximum:

Sheets per pass ........................................................................................................... 10*

Cards per pass ............................................................................................................... 1*

Paper entry width 9 in. (230mm) ........................................................................................

* 8.5 in. x 11 in., 20lb., paper at 120V/60 Hz, 2.5Amps; heavier paper, humidity (75g)

or other than rated voltage may reduce capacity. Maximum recommended daily usage rates:

200 sheets; 5 credit cards. 10 sheets per pass.

Fellowes SafeSense® shredders are designed to be operated in home and office environments ranging

between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.

• Operation,maintenance,andservicerequirementsarecoveredinthe

instruction manual. Read the entire instruction manual before operating

shredders.

• Keepawayfromchildrenandpets.Keephandsawayfrompaperentry.

Always set to off or unplug when not in use.

• Keepforeignobjects–gloves,jewelry,clothing,hair,etc.–awayfrom

shredder openings. If object enters top opening, switch to Reverse ( ) to

back out object.

• Never use aerosol products, petroleum based lubricants or other flammable

products on or near shredder. Do not use canned air

on shredder.

• Donotuseifdamagedordefective.Donotdisassembleshredder.Donot

place near or over heat source or water.

• ThisshredderhasaDisconnectPowerSwitch(E)thatmustbeintheON(I)

position to operate shredder. In case of emergency, move switch to OFF ( )

position. This action will stop shredder immediately.

• Avoidtouchingexposedcuttingbladesundershredderhead.

• Shreddermustbepluggedintoaproperlygroundedwalloutletorsocketof

the voltage and amperage designated on the label. The grounded outlet or

socket must be installed near the equipment and easily accessible. Energy

converters, transformers, or extension cords should not be used with this product.

• FIREHAZARD–DoNOTshredgreetingcardswithsoundchipsorbatteries.

• Forindooruseonly.

• Unplugshredderbeforecleaningorservicing.

IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!

www.fellowes.com features an extensive on-line support section with a number of self-service options

Press Auto On ( )

to activate

Feed paper/card

straight into paper

entry and release

When finished

shredding set to

OFF ( )

PAPER/CARD

Plug in and put

disconnect power

switch in ON (I) position

Continuous operation: up to 8 minutes maximum

NOTE: Shredder runs briefly after each pass to clear

entry. Continuous operation beyond 8 minutes will

trigger 20-minute cool down period.

BASIC SHREDDING OPERATION

KEY

G. Control Switch and Indicator lights

1. Reverse

2. OFF

3. Auto On (blue)

4. SafeSense

indicator (yellow)

5. Overheat (red)

6. Door open/Bin full (red)

7. Remove Paper (red)

A. SafeSense

Technology

B. Paper entry

C. Pull-out Bin

D. Window

E. Disconnect power switch

1. OFF

2. ON

F. See safety instructions

21 3 4

SET-UP AND TESTING

Set to Auto On ( ) Touch test area and

look for the SafeSense

indicator to illuminate

SafeSense

is active and

working properly

If hand is held on SafeSense

area more than 3 seconds

shredder will shut off

SAFESENSE® TECHNOLOGY

Stops shredding immediately when hands touch the

paper opening.

WHEN IN SLEEP MODE

ENERGY SAVING SYSTEM

• Savesenergyinfourways:energy-efficientelectronics,jamprevention,

standby mode and sleep mode.

• SleepModeshutsdownshredderafter2minutesofinactivity.

Optimal energy efficiency 100% of

the time – in use and out of use.

In sleep mode To get out of sleep mode

set to OFF ( ), then

Auto On ( )

Insert paper

For more information about all of Fellowes Advanced Product Features go to www.fellowes.com

JAM BLOCKERTM

ADVANCED PRODUCT FEATURES

Blocks jams before they start

If Remove Paper

icon illuminates during the shredding process

(due to paper misfeed or wrinkle) follow the procedures below.

Patented SafeSense® Technology

Stops shredding immediately when

hands touch the paper opening

Jam BlockerTM

Blocks jams before

they start

Reduce paper quantity

to an acceptable

amount and refeed

into paper entry

Set to Reverse ( )

and remove paper

Set to Auto On ( ) and

refeed into paper entry

Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.

*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250

PRODUCT MAINTENANCE

All cross-cut shredders require oil for peak performance.

If not oiled, a machine may experience diminished sheet

capacity, intrusive noise when shredding and could ultimately

stop running. To avoid these problems, we recommend you

oil your shredder each time you empty your waste bin.

OILING SHREDDER

FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE

*Apply oil across entry

Set to OFF ( )

Set to Reverse

( )

for 2-3 seconds

TROUBLESHOOTING

Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This

indicator will remain illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about

the continuous operation and recovery time for this shredder.