Fellowes Microshred 12Ms Handleiding

Fellowes Papiervernietiger Microshred 12Ms

Lees hieronder de 📖 handleiding in het Nederlandse voor Fellowes Microshred 12Ms (8 pagina's) in de categorie Papiervernietiger. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

PLEASE READ THESE INSTRUCTIONS BEFORE USE.

DO NOT DISCARD: KEEP FOR FUTURE REFERENCE.

VEUILLEZ LIRE CES INSTRUCTIONS AVANT D’UTILISER L’APPAREIL.

NE PAS JETER : CONSERVER AFI N DE CONSULTER LES DIRECTIVES ULTÉRI-

EUREMENT, EN CAS DE BESOIN.

LEA ESTAS INSTRUCCIONES ANTES DEL USO.

NO LAS DESECHE: CONSÉRVELAS COMO REFERENCIA FUTURA.

AD THE

KEE

AVANT D’

L’A

N DE

LTE

LTÉ

Microshred 12Ms

The World's Toughest Shredders®

CAPABILITIES

ENGLISH

Model 12Ms

KEY

G. See safety instructions

H. LEDs

1. ON/OFF (white)/Bin Open

2. Overheat (red)

3. Bin full (red)

4. Remove Paper (red)

5. SafeSense

indicator (yellow)

Will shred: Paper, plastic credit cards, staples and small paper clips

Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper, cardboard,

large paper clips, folders, X-rays, CD/DVD or plastic other than noted above

Paper shred size:

Micro-Cut .....................................................................5/32 in. x 1/2 in. (4mm x 12mm)

Maximum:

Sheets per pass ........................................................................................................... 12*

Cards per pass ............................................................................................................... 1*

Paper entry width .....................................................................................8.7 in. (220mm)

* 8.5 in. p2-x11 in., 20lb., (75g) paper at 120V, 60 Hz, 3.9 Amps; heavier paper, humidity or other than

rated voltage may reduce capacity. Maximum recommended daily usage rates: 1000 sheets per day, 25

credit cards.

Fellowes SafeSense® shredders are designed to be operated in home and office environments ranging

between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.

BASIC SET UP

A. SafeSense

Technology

B. Paper entry

C. Control Panel

1. Reverse

2. Forward

D. Pullout bin

E. Casters

F. Disconnect power switch

1. OFF

2. ON

IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!

t 0QFSBUJPONBJOUFOBODFBOETFSWJDFSFRVJSFNFOUTBSFDPWFSFEJOUIFJOTUSVDUJPO

manual. Read the entire instruction manual before operating shredders.

t ,FFQBXBZGSPNDIJMESFOBOEQFUT,FFQIBOETBXBZGSPNQBQFSFOUSZ"MXBZTTFU

to off or unplug when not in use.

t ,FFQGPSFJHOPCKFDUToHMPWFTKFXFMSZDMPUIJOHIBJSFUDoBXBZGSPNTISFEEFS

openings. If object enters top opening, switch to Reverse ( ) to back out object.

t %0/05VTFBFSPTPMQSPEVDUTQFUSPMFVNCBTFEPSBFSPTPMMVCSJDBOUTPOPSOFBS

shredder. DO NOT USE “CANNED AIR” OR “AIR DUSTERS” ON SHREDDER. Vapors

from propellants and petroleum based lubricants may combust causing serious

injury.

t %POPUVTFJGEBNBHFEPSEFGFDUJWF%POPUEJTBTTFNCMFTISFEEFS

Do not place near or over heat source or water.

t 5IJTTISFEEFSIBTB%JTDPOOFDU1PXFS4XJUDI'UIBUNVTUCFJOUIF0/( )

position to operate shredder. In case of emergency, move switch to OFF ( )

position. This action will stop shredder immediately.

t "WPJEUPVDIJOHFYQPTFEDVUUJOHCMBEFTVOEFSTISFEEFSIFBE

t 4ISFEEFSNVTUCFQMVHHFEJOUPBQSPQFSMZHSPVOEFEXBMMPVUMFUPSTPDLFUPGUIF

voltage and amperage designated on the label. The grounded outlet or socket

must be installed near the equipment and easily accessible. Energy converters,

transformers, or extension cords should not be used with this product.

t '*3&)";"3%o%P/05TISFEHSFFUJOHDBSETXJUITPVOEDIJQTPSCBUUFSJFT

t 'PSJOEPPSVTFPOMZ

t 6OQMVHTISFEEFSCFGPSFDMFBOJOHPSTFSWJDJOH

CASTER INSTALLATION

1 3 42

BASIC SHREDDING OPERATION

Continuous operation:

Up to 30-minutes maximum

NOTE: Shredder runs briefly after

each pass to clear entry. Continuous

operation beyond 30-minutes will

trigger 10-minute cool down period.

Feed paper/card

straight into paper

entry and release

Plug in and put

disconnect power

switch in ON (I) position

When finished

shredding set

to OFF ( )

Press and hold forward ( )

2-3 seconds

PRODUCT MAINTENANCE

CLEANING AUTO-START INFRARED SENSORS

Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors

may become blocked by paper dust causing the motor to run even if there is no paper present.

(Note: two paper detection sensors are located in the center of the paper entry).

All micro-cut shredders require oil for peak performance. If not oiled, a

machine may experience diminished sheet capacity, intrusive noise when

shredding and could ultimately stop running. To avoid these problems, we

recommend you oil your shredder each time you empty your waste bin.

OILING SHREDDER

*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250

FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE

*Apply oil across entry

TO CLEAN THE SENSORS

Turn off and unplug

shredder

Locate Auto-start

infrared sensor

Dip cotton swab in

rubbing alcohol

Using cotton swab, wipe

away any contamination

from the paper sensors

For more information about all of Fellowes Advanced Product Features go to www.fellowes.com

Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain

illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and

recovery time for this shredder.