Extron MPA 401-100V Handleiding

Bekijk gratis de handleiding van Extron MPA 401-100V (2 pagina’s), behorend tot de categorie Receiver. Deze gids werd als nuttig beoordeeld door 7 mensen en kreeg gemiddeld 4.7 sterren uit 8 reviews. Heb je een vraag over Extron MPA 401-100V of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1

MPA 401-70V and MPA 401-100V • Setup Guide

This guide provides basic instructions for an experienced installer to install and congure the

Extron MPA 401-70V and MPA 401-100V mini power ampliers.

INPUTSOUTPUT

50/60 Hz

100-240V .3A

2

134

LRLR

LR

LR

LR

AUDIO

VID

123

4

Y

/VID

B-YH/

HV

R

/R-Y

V

G

/Y

B

/B-Y

RS-232

LAN

RESET

ACTLINK

DVI

C

SDIR-Y

/C

RGB/R-Y,Y,B-Y/YC/VID

I

N

P

U

T

O

U

T

P

U

T

Extron

SI 3CT LP

Full-Range

Ceiling Sspeaker

Extron

MPA 401

Mini Power

Amplier

Extron

DVS 4 DVI 30AD

Digital V ideo

Scaler

with Audio

Audio

Ft P laanel

Display

(DVI)

DSS Rverecei

(S-video)

Laptop

(RGB)

DVD

(Component)

VCR

(Video)

Ext50ron VC

Vole Cr umontrolle

Extron

MLC 4 10IPPlus

Controller

POWER

12V

1.5A MAX

CLASS 2 WIRING

L

(SUMM

(SUMMED)

R

VCG

MPA 401-100V

R

L

10V50mA

REMOTE100V OUTPUT

INPUTS

VC 50

Extron

VOLUME

DBS RECEIVER

CONFIG

DISPLAY

MLC 104 IP

E

1

2

3

4

ON

OFF

Step 1 — Turn all of the equipment off and disconnect all power sources.

Step 2 — Mount the amplier in either a plenum space, on a rack, under a desk, or on a projector.

ATTENTION:Although the amplier is plenum rated, the power supply provided with it is not. The power supply must not be

placed in the plenum space. Cables to and from the amplier must be plenum rated.

NOTE:Use only the two round mounting holes for mounting the MPA 401. The other four (hexagonal) holes anchor stand-offs

for the internal circuit boards. Using them may damage the amplier and does not provide secure mounting for the unit.

Step 3 — Attach the speakers to the MPA 401 using the 2-pole, 5 mm screw-lock

captive screw speaker receptacle on the rear panel. (The old and new silk screens for the

MPA401-100V are shown to the right).

ATTENTION:Do not ground or short the speaker outputs as this will damage the

amplier.

NOTE:The mono audio speaker receptacle may be labeled in one of two ways (see

the images to the right). The wiring and function are the same whichever way the

product is labeled.

Step 4 — Attach sources to the MPA 401 unit from the audio source or projector.

The three rear panel audio inputs can be used individually or together:

zOne pair of RCA receptacles (unbalanced)

zOne 3.5 mm stereo tip-ring-sleeve receptacle (unbalanced)

zOne 3.5 mm, 5-pole captive screw receptacle (balanced or unbalanced)

Balanced Mono Input

Tip

Ring

Sleeve

LR

Balanced Stereo Input

Tip

Ring

Tip

Ring

Sleesve

LR

Unbalanced Stereo Input

Tip

Slee

ve

Slee

ve

Tip

LR

Unbalanced Mono Input

Tip

Sleeve

LR

CLASS 2 WIRING

100V OUTPUT

Tip (+)

Slee ( )ve

RCA Connector

Slee ( )ve

Ring (R)

Tip (L)

3.5 mm TRS Connector

OUTPUT

100V

Product specificaties