Extreme Networks AP5020 Handleiding

Bekijk gratis de handleiding van Extreme Networks AP5020 (3 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.6 sterren uit 7 reviews. Heb je een vraag over Extreme Networks AP5020 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Extreme Wireless 802.11be

Wi-Fi 7 Indoor AP5020

Technical Specifications

Overview of AP5020

The AP5020 is a high-performance 802.11ax Wi-Fi 7E, 6 GHz, 5 GHz band, and

2.4 GHz band AP for high-density indoor environments. The AP supports IEEE

802.11ax Orthogonal Frequency-Division Multiple Access (OFDMA) multi-user

access. It can be installed on a ceiling rail, on a non-standard ceiling, or on a

wall.

The AP5020 access point has the following features and

specifications. For more information, see the AP5020

Data sheets .here

Fig. 1 .AP520

Radios

- 3 radios (2.4GHz, 5 GHz and 6 GHz).

- 2 IoT radios (Thread, Zigbee®, Bluetooth 5.4 Low Energy,

IEEE802.15.4).

Ports

Two Ethernet ports with RJ45 connectors:

- 1 x 100/1,000/2,500/5,000/10,000Mbps auto-sensing

link speed Ethernet port, PoE PD.

- 1 x 100/1,000/2,500/5,000 Mbps autosensing link speed

Ethernet port, PoE PD in or 802.3af 15.4W PSE out mode

(requires 802.3bt on Eth0).

One USB port:

- USB 2.0, Type A, 5V/400mA with with PoE 802.3at or

5V/1,000mA with PoE 802.3bt

Security

- One Kensington security slot.

- Trusted Platform Module (TPM)

Power Options

- Power draw: 802.3at PoE: typical 21W, max. 25.5W

(802.3at profile) without PoE out or USB

- Power draw: 802.3bt: max. 35W with 5W USB

- 12V/3A DC. DC power has priority when both DC and

PoE power sources are available.

- PoE failover or optional PSE out supported

- With DC power in, USB 5W power is supported.

Use these instructions as guidelines for mounting and

connecting the AP5020 access point easily and safely.

The AP5020 comes with the AH-ACC-BKT-AX-TB

mounting bracket that can be used to mount the access

point on flat t-bar ceiling grids and flat surfaces.

Electrical Hazard:Only qualified personnel should

perform installation procedures.

The AP5020 has one status light on top of the chassis. It

shows operational states for power, firmware updates,

Ethernet and wireless interface activity, and major

alarms.

Table 4. ExtremeCloud® IQ LED Activity

LEDDescription

DarkPower is off.

Solid whiteThe device power is on and the AP is ready

to use.

The device has successfully established a

Control And Provisioning of Wireless Access

Points (CAPWAP) connection to Extreme-

Cloud IQ and is operating normally.

Slow-blinking

white

The device has a CAPWAP connection to

ExtremeCloud IQ, but is operating on 802.3at

power instead of 802.3bt power.

Solid amber:The device power is on and the access point

is in boot up mode, or is running without a

CAPWAP connection.

Slow-blinking

amber:

The device has no CAPWAP connection to

ExtremeCloud IQ, and is operating on 802.3at

power instead of 802.3bt power.

Fast-blinking

amber

The device is updating its IQ Engine firm-

ware.

Table 5. ExtremeCloud IQ Controller Status LED Activity

LEDDescription

Dark: Power is off or the AP is taken over by the

controller. Configuration pushes down to AP

from controller to turn off the LED.

Solid whiteThe AP is starting up or is already taken over

by the controller.

Slow-blinking

white

The AP is being taken over by the controller

or has failed to be taken over by the control-

ler.

Physical Dimensions

- 10.16 in. x 10.16 in. x 1.62 in. (258mm x 258mm x 41mm).

- Weight: 3.57 lbs (1.62 kgs).

Internal Antenna:

- (4) Dual band 2.4 GHz and 5 GHz

- (4) Single band 6 GHz

- (2) 5 GHz/6 GHz sensor

- (3) IoT sensor

Temperature:

- Operating: 0°C to 50°C (32°F to 122°F).

- Storage: 0°C to 70°C (32°F to 158°F).

- Humidity: 0% to 95% (non-condensing ).

Enclosure: Plastic Top, Aluminum Bottom.

Fig.2 AP520 Ports

ItemPort

1

USB 2.0 type A port, 5V/400mA with PoE

802.3atPoE 802.3bt or 5V/1,000mA with

2Console port. The console port can only be used

with the Extreme Networks console cable. You

will damage the AP if you use another cable.

3Kensington security slot

Table 1. AP5020 Ports and Connections

Status LED Activity Description

Through the console port, you can make a serial connec-

tion between your management system and the access

point.

Use the SKU ACC-WIFI-MICROUSB if you need to order

the Micro USB cable. The console port can only be used

with the Extreme Networks console cable. You will dam-

age the AP if you use another cable.

Micro USB Console Port

QuantityItem

1AP5020 Access point

1AH-ACC-BKT-AX-TB mounting bracket

1Regulatory guide

2Philips pan head wood screws

2Phillips head plastic screw-in anchors

Fig. 4. AH-ACC-BKT-AX-TB bracket red dot

Connect a Power Supply

Position the Access Point before Installation

Line up the red dot on the access point and the bracket

for ease of installation. The AP and bracket lock in place.

Table 3. AP5020 Box contents

Fig. 3 AP520 Ports

AP5020 Box Contents

Confirm that the following items shipped with your

AP5020 before you begin the installation. If any items are

damaged or missing, then contact your dealer.

ItemPort

112VDC

2ETH1 port

3ETH0/PoE port

Table 2. AP5020 Ports and Connections

Install the Access Point on a Standard Flat

Ceiling Rail with Sculpted Ceiling Tiles

The AP ships with a mounting bracket for standard 15/16”

(24mm) wide t-bars or 9/16” (14mm) wide t-bar rails.

For nonstandard ceiling rail installations, see “Install the

Access Point on a Non-standard Ceiling Grid or a Wall”

on page 2.

1. Remove the ceiling tiles.

2. Align the accessory on the ceiling rail so that the

accessory metal hinges are almost parallel to the

sides of the ceiling rail.

3. Rotate the accessory clockwise until the metal

hinges hook over the edge of the rail and the white

tabs click in place.

Note: The two white tabs on the back of the

accessory hold the ceiling rail in place.

Use your finger and to push and to unhook one

side of the white tab if you want to remove the

accessory from the ceiling rail.

If you require an external 12V DC power supply, you can

plug the power cord into the power connector found on

the back of the AP by the RJ-45 connector.

The LED on the top of the access point lights up white

when you connect the power supply.

For information see ExtremeWireless Access Point

AP5020 Installation Guide.

LEDDescription

Flashing

fading

white:

Configuration pushes down to AP from con-

troller helping the user

locate the AP by sight.

Solid amberA firmware upgrade is occurring.

Fast-blinking

amber

The AP is acquiring the DHCP IP.

Product specificaties