Extech 380400 Handleiding
Extech
Niet gecategoriseerd
380400
Bekijk gratis de handleiding van Extech 380400 (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 58 mensen en kreeg gemiddeld 4.9 sterren uit 29.5 reviews. Heb je een vraag over Extech 380400 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/1
3 - -GB_V1.5 9/19 80400 en
User Manual
Resistance Decade Box
Model 380 0 40
Introduction
Congratulations on your purchase of the Extech 380400 Resistance Decade Box. This device
oers 7 decades of resistance ranges from 1 to over 11MOhms (in 1Ohm steps). Slide switches
allow easy addition and subtraction of resistance values. Binding posts (3) oer simp and le
secure connections. Careful use of this decade box will provide years of reliable service.
Specications
Resistance ranges 1 to 11,111,110 Ohms in 1 Ohm steps
Internal Resistance 0.3 Ohms
Power 0.3W Resistors
Connection Three (3) binding posts
Accuracy 1% Reading) + 0.3 Ohms ±(
Operating conditions Temperature: 32 to 122oF (0 to 50oC) / Humidity: 80%RH <
Dimensions/Weight 5.79 x 4.61 x 1.3" (14.7 x 11.7 x 3.3 Approx. 0.69 lbs. (312 cm) / g)
Operation
Binding Post Connections
The binding posts can be used for connections in several ways:
1. A banana plug can be inserted directly into the posts.
2. Bare wire can be threaded through the post after it has been unscrewed. Once the bare wire is threaded, tighten the posts as
necessary.
3. Alligator clips can be used but use caution not to strip the post threads or plastic post housing.
The resistance output is available on the RED and the BLACK binding posts. The WHITE post is case ground and is typically not
used. Connect the positive lead of the device under test to the RED post. Connect the negative lead to the BLACK post. Use the
WHITE grounding post only if the device under test will be grounded to the 380400 case.
Range Selection
The front panel switches are used to select the resistance that will be available on the RED and BLACK terminals. When a switch 28
is set to the IN position, the value printed above the switch is added to the total resistance available at the posts. When the switch is
set to OUT it is excluded from the total resistance. If all of the switches are set to OUT, the total output resistance zero (+ 0.3Ohms is
internal resistance approx.). –
For example, if the desired output value is 10.5KOhms, set the following switches to the IN position: 10K, 400Ohms and 100Ohms , .
Testing
This device can be used to verify the calibration integrity of MultiMeters, LCR meters, Calibrators, etc. Connect as described above in
the Binding Post Connection section. Set the resistance switches to output the desired resistance. Ensure that the voltage supplied
by the device under test does not overload the 0.3W internal resistor power rating. The device under test should read the value of
resistance selected on the tester. If it does not, the device under test may need calibration, adjustment, or repair.
Copyright - FLIR Systems, Inc. ©2013 2019
All rights reserved including the right of reproduction in whole or in part in any form
www.extech.com
Product specificaties
| Merk: | Extech |
| Categorie: | Niet gecategoriseerd |
| Model: | 380400 |
Heb je hulp nodig?
Als je hulp nodig hebt met Extech 380400 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Extech
22 Oktober 2024
25 Juni 2024
25 Maart 2024
25 Maart 2024
25 Maart 2024
11 December 2023
6 December 2023
26 Juni 2023
31 Mei 2023
28 Mei 2023
Handleiding Niet gecategoriseerd
- Maretron
- Vishay
- Blackmagic Design
- Mermade
- Europalms
- ProForm
- Start International
- Philco
- EQ3
- Teenage Engineering
- Palson
- BigBlue
- CTA Digital
- Fire Magic
- Elba
Nieuwste handleidingen voor Niet gecategoriseerd
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025