Estella CMPT16A Handleiding
Estella
Crepemaker
CMPT16A
Lees hieronder de 📖 handleiding in het Nederlandse voor Estella CMPT16A (11 pagina's) in de categorie Crepemaker. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.8 sterren beoordeeld
Pagina 1/11
# 3 4 8 C M PT 1 6 A • SINGLE
# 3 4 8 C M X 1 6 D B L M • DOUBLE
C R E P E M A K E R S
CONFORMS TO UL STD. 197
CONFORMS TO NSF/ANSI STD. 4
5025815 5025815
U S E R M A N U A L
200°F
150°F
250°F
350°F
5
50 °F
HI
MIN
w w w. E s te l l a E q u i p m e n t .c o m2
S E R I A L P L A T E
The serial plate is located on the back of the unit.
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
All equipment should be examined for damage before and during
unloading. The freight carrier has assumed responsibility for its safe
transit and delivery. If equipment is received damaged, either apparent
or concealed, a claim must be made with the delivering carrier.
a) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed by
the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can supply
the necessary forms.
b) If concealed damage is not apparent until after equipment is uncrated, a request for inspection must be
made to the carrier within 5 days. The carrier should arrange an inspection. Be certain to hold all contents
and packaging material.
Installation and service should be performed by a qualified installer who thoroughly reads, understands, and
follows these instructions. If you have questions concerning the installation, operation, maintenance, or service
of this product, visit Estella Equipment at www.estellaequipment.com.
I N D E X
Introduction .................................................... 2
Location Of Data Plate ................................ 2
Safety Precautions ...................................3, 4
Note For The First Time Use 4 .....................
Seasoning The Griddle ............................... 5
Operating Steps ........................................6, 7
Care And Cleaning ....................................... 8
Tips And Maintenance ..................... 8, 9, 10
Digital Board Error
Code Troubleshooting ...............................10
General Troubleshooting Issues ........11, 12
I N T R O D U C T I O N
Congratulations on your purchase of Estella Equipment. Estella Equipment takes pride in the design and quality
of our products. When used as intended and with proper care and maintenance, you will experience years
of reliable operation from this equipment. To ensure best results, it is important that you read and follow the
instructions in this manual carefully.
Item: 348CMPT16A
Product Description:
SINGLE CREPE MAKER, PORTABLE
Voltage: Wattage: | 120V 2300W
Phase: Hertz: | 1 Phase 60 Hertz
Amperage: Plug Type: | 19A 5-20P
Serial NUMBER:
CONTROL#
WARNING! Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating, and
maintenance instructions thoroughly before installing or serving this equipment.
Commercial use only. Disconnect from electric supply before adjustment, WARNING!
alteration, service or maintenance. Do not immerse in water.
MADE IN CHINA
CONFORMS TO UL STD. 197
CONFORMS TO CSA C22.2 NO. 109
CONFORMS TO NSF/ANSI STD. 4
Example of serial plate.
w w w. E s te l l a E q u i p m e n t .c o m3
S A F E T Y P R E C A U T I O N S
Notice: This product is intended for commercial use only. Not for household use.
Notice: Local codes regarding installation vary greatly from one area to another. The National Fire Protection
Association, Inc., states in its NFPA96 latest edition that local codes are “Authority Having Jurisdiction” when it
comes to requirements for installation of equipment. Therefore, installation should comply with all local codes.
Warning: For your safety, do not store or use gasoline or other flammable vapors or liquids in the vicinity of this
or any appliances. Keep the area free and clear of combustible materials. (See ANSI Z83. 14B, 1991.)
Warning: Improper installation, adjustment, alteration, service, or maintenance can cause property damage,
injury, or death. Read the installation, operating, and maintenance instructions thoroughly before installing or
servicing this equipment.
Caution: These models are designed, built, and sold for commercial use only. If these models are positioned so
the general public can use the equipment, make sure that cautions, warnings, and operating instructions are
clearly posted near each unit so that anyone using the equipment will use it correctly and not injure themselves
or harm the equipment.
Warning: A factory authorized agent should handle all maintenance and repair. Before doing any maintenance
or repair, contact your authorized service representative.
Warning: An earthing cable must connect the appliance to all other units in the complete installation and from
there to an independent earth connection.
Notice: When installed, the unit must be electrically grounded and comply with local codes, or in the absence
of local codes, with the national electrical code ANSI/NFPA70- latest edition. Canadian installation must comply
with CSA-STANDARD C.22.2 Number 0 M1 982 General Requirements-Canadian Electrical Code Part ll, 109-
M1981- Commercial Cooking Appliances. Do not use unit with a damaged cord or plug, in the event the appli-
ance malfunctions, or has been damaged in any manner.
Warning: SHOCK HAZARD - Turn OFF all power to equipment before cleaning the equipment.
THE FOLLOWING SAFETY PRECAUTIONS MUST BE OBSERVED WHEN USING THIS PRODUCT:
1. Please read the relevant instructions carefully before using this product.
2. Do not share the same power source with other high-power appliances to avoid excessive power load and
other dangers.
3. The surface temperature of this product is very hot after operation. Burns may be caused by contact with
hot parts.
4. Keep machine away from children and non-authorized personnel. Do not permit them to go near the
machine or its working area.
5. Do not allow this product to be used unattended.
6. Do not touch the power cord with sharp objects or high-temperature surfaces to avoid damage to the
power cord.
7. Check that the machine is not damaged prior to each use. Carefully check that all safety devices are working,
that the removable parts are not blocked, there are no parts damaged, that all the parts have been set up
correctly, and that all conditions that could influence the regular function of the machine are in working
order. If the machine is damaged or there are issues during its use, turn off the machine immediately and
contact the manufacturer for assistance or repair. Repairs should only be made by qualified technicians,
using the correct manufacturer parts. Non-compliance with these rules may void the warranty.
Continued on next page.
Product specificaties
| Merk: | Estella |
| Categorie: | Crepemaker |
| Model: | CMPT16A |
Heb je hulp nodig?
Als je hulp nodig hebt met Estella CMPT16A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Crepemaker Estella
11 Juni 2025
Handleiding Crepemaker
- Crepemaker Rommelsbacher
- Crepemaker Vox
- Crepemaker Caso
- Crepemaker Orbegozo
- Crepemaker Cloer
- Crepemaker Duronic
- Crepemaker Bartscher
- Crepemaker Emerio
- Crepemaker Severin
- Crepemaker Proctor Silex
- Crepemaker CombiSteel
- Crepemaker Salton
- Crepemaker Livoo
- Crepemaker Royal Catering
- Crepemaker Maxwell
Nieuwste handleidingen voor Crepemaker
11 Juni 2025
10 Juni 2025
9 Juni 2025
6 Juni 2025
19 Februari 2025
14 Oktober 2024
14 Oktober 2024
14 Oktober 2024
7 December 2023
26 November 2023