Equip Wall bracket 650200 Handleiding

Bekijk gratis de handleiding van Equip Wall bracket 650200 (2 pagina’s), behorend tot de categorie Flat panel steun. Deze gids werd als nuttig beoordeeld door 14 mensen en kreeg gemiddeld 4.6 sterren uit 2 reviews. Heb je een vraag over Equip Wall bracket 650200 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

LCD TV WALL MOUNT BRACKET

FIXED

Universal | 650200

Features

lSupports 58 ~ 94cm (23” ~ 37”) Flat Panel Display

lDistance from TV to Wall: 30mm

lVESA Mount Standards: Maximum 400 x 200mm

lHole Pattern: Maximum 430mm Wide and 205mm High

lUniversal Mounting Pattern

lBubble Level Integrated

lLoad Capacity: Maximum 75kg (165lbs)

WARNING!

Make sure that any listed parts are not missing or defective. Improper installation would result in personal injury

or damage to equipment. If you have any questions about installation, please visit http://www.equip-info.net for

more assistance.

Hardware Kit

Note:Any of the hardware in kit will be required. Other joint parts are forbidden.

INSTALLATION

Attach the Arms to the Display

1. Use the correct length screws on your display with different back as below.

A. For flat back, use one of the shorter screws from the hardware kit.

B. For curved or recessed back, use one of the longer screws from the hardware kit.

2. Use the correct diameter screws after carefully trying each screw from the hardware kit.

Do not apply too much force to any of the screws. If you feel force resistance, stop immediately to use smaller

diameter screws.

3. Attach 2 arms to the different back of your display, using the correct screws along with corresponding

washers○

kas mentioned below A. & B.

A. If you use the M4 or M5 screws, you will need to use the small hole of washers.

B. If you use the M6 screws, you will need to use the large hole of washers.

C. If you are using one of the longer screws on the curved or recessed back of your display, you will also needto

use the small spacer○

jfor M4 or M5 or M6 screws.

4. Make sure all screws are secured, but do not over-tighten them.

Diagram-1Diagram-2 (Flat Back)Diagram-3 (Curved / Recessed Back)

Assemble the BracketDiagram-4

1. Assemble 4 brackets with 4 screws○

c

2. Make sure the brackets are joined together firmly.

Mount the Wall Plate on the Wall

(a) Wooden Wall - The wall plate must be secured to two adjacent wood studs at least 16” apart.

1. Using a stud finder, locate and mark two adjacent studs for securing the mount.

2. Place the wall plate against the wall andlevel it by using the bubble guide.

3. Make two locations (two per stud) on the wall where the mount will be secured.

4. Remove wall plate and then drill a (4mm) pilot hole at each location with an electric drill.

5. With another person’s help, replace the wall plate and fix it to the wall by using the lag

bolts○

iand lag bolt washers○

lprovided.

6. Do not over-tighten the bolts and do not release the wall plate until all screws are secured.

Diagram-5

(b) Concrete Wall

1. Place the wall plate against the wall and level it by using the bubble guide.

2. With another person’s help, mark off 4 locations for fixing the mount to the wall.

3. Place the wall plate aside and drill a hole at each location using a 3/8” (10mm) masonry bit.

4. Insert one concrete anchor ○

hinto each hole. A hammer can be used to lightly tap the anchors into place if

necessary.

5. With another person’s help, replace the wall plate and fix it to the wall by using the lag bolts○

iand lag bolt

washers○

lprovided.

6. Do not over-tighten the bolts and do not release the wall plate until all screws are secured.

Diagram-6

Adjustment

1. With another person’s help, carefully lift your display and place it on the wall plate. Do not release the display

until the mounting arms have securely hooked onto the mount.

2. Move the safety lock as shown in the picture and tighten the two screws to fix the safety lock.

Product specificaties