Equip 129503 Handleiding

Equip Tang 129503

Bekijk gratis de handleiding van Equip 129503 (7 pagina’s), behorend tot de categorie Tang. Deze gids werd als nuttig beoordeeld door 29 mensen en kreeg gemiddeld 4.4 sterren uit 15 reviews. Heb je een vraag over Equip 129503 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/7

Cable Tester NS-468

Safety instructions

· Do not use the cable tester NS-468 if it is damaged.

· This device is only for use inside dry and clean rooms.

· This device must be protected from moisture, splash water and impact of heat .

Intended use

The cable tester is used for fast testing of ISDN-, and network cable (RJ11, RJ45).

Configuration and shielding will be tested. Installed cable could be also tested.

Another employment than indicated is not permissible!

Changes can lead to the damage of this product, beyond that is this connected with dangers, like e.g.

short-circuit, fire, electrical impact etc.

For all special and personal injuries, which occur of not intended use, not the manufacturer, but the

operator is responsible.

Please note that serving and/or connection errors lie outside of our sphere of influence.

Understandably we cannot take over any adhesion for damage, which occur from it.

The entire product may not be changed and/or converted!

Preparation / Measurement

No energized lines measure!

Insertion of battery:

To insert the battery (9 V-Block) remove battery cover from MASTER-Device. Connect the battery

clip to the battery.

For operations of the REMOTE-device there is no battery needed.

Plugs / Cable:

1- 2-

RJ45 RJ12 / RJ11

Measurement:

· Connect the plugs of the cable which can be measured with the suitable sockets of the

MASTER and the Remote device.

· By pushing the switch to „ON“ -Position you turn the device to „FAST Test Modus“. Here each

individual contact of the cable is successively examined. The electrical connection is indicated

at the MASTER and at the REMOTE device over an LED.

· By pushing the switch to „S“-Position you turn the device to „SLOW Test Modus.

· By pushing the switch to „OFF“-Position you turn the device off.

· The result of measurement is indicated over the status LEDs (see table of the most usual

connections) at both devices. At cable with shielding shines additionally the “G “- LED

Kabel Stecker Anzeige MASTER Anzeige REMOTE

Cable Display

Master

Display

Remote

RJ45-Network cable (1:1,

completely connected, with

shielding)

1-2-3-4-5-6-7-8-G 1-2-3-4-5-6-7-8-G

RJ45-Network cable (crossover,

completely connected, without

shielding)

1-2-3-4-5-6-7-8 1-4-3-2-5-6-7-8

ISDN-Cable, 4-pin 3-4-5-6 3-4-5-6

RJ12-Cable, 6-pin 1-2-3-4-5-6 1-2-3-4-5-6

RJ11-Cable, 4-pin 2-3-4-5 2-3-4-5

Product specificaties

Merk:	Equip
Categorie:	Tang
Model:	129503
Kleur van het product:	Meerkleurig
Gewicht:	625 g
Breedte:	120 mm
Diepte:	55 mm
Hoogte:	215 mm
Gewicht verpakking:	584 g
Breedte verpakking:	12 mm
Diepte verpakking:	8 mm
Hoogte verpakking:	8 mm
Soort:	Gereedschapset