Eltax Shine 5-pack Handleiding

Eltax Luidspreker Shine 5-pack

Lees hieronder de 📖 handleiding in het Nederlandse voor Eltax Shine 5-pack (12 pagina's) in de categorie Luidspreker. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
Shine 5-pack
Danish Sound Since 1959
Instruction manual
Betriebsanleitung
Mode d’emploi
Instruktionsvejledning
Manuale d´istruzioni
Gebruiksaanwijzing
Manual de instrucciones
Instruction manual
Thank you for purchasing Eltax loudspeakers. You have just purchased one of the best domestic
hiî‚¿ loudspeakers available and we hope you will enjoy the music they reproduce for many years
to come. The following notes are designed to assist you in obtaining a greater degree of musical
satisfaction from your Eltax loudspeakers. Before connecting your loudspeakers, we suggest that
you read this leaet carefully.
Amplier capacity/power handling
Your Eltax loudspeaker system will operate satisfactorily with any good ampliî‚¿er designed for
use with an 4-8 Ohm impedance load. Allthough Eltax loudspeakers are designed to handle high
power loadings, you must remember that any loudspeaker that is abused with excessive use of
volume, tone controls and graphic equalisers is likely to cause damage to the drive-units. Be carefull
especially with small ampliî‚¿ers constantly driven on high power levels as these may be liable to
go into »clipping mode« and disort the signal causing possible damage. If you hear a distordet
signal through the loudspeakers you must reduce the power level.
Connecting to your amplier
We strongly recommend the use of high quality speaker cables, colour coded or grooved cables
are recommended to assist checking polarity, your local dealer should be able to advise you on
this point. Always switch OFF your ampliî‚¿er before making any connections or adjustments to
the system. Wire the right-hand channel cable so that the positive (RED) terminal of your loud-
speaker is connected to the positive (RED) on your ampliî‚¿er, and the negative (BLACK) terminal
of your loudspeaker is connected to the negative (BLACK) terminal on your ampliî‚¿er. Repeat
the instructions for all channels. Do NOT connect more than one loudspeaker to one terminal on
your ampliî‚¿er.
Phasing
Providing that you have followed the connecting instruction correctly the loudspeakers should be
in phase and provide solid stereo images. If, however, you have any doubt as to the phasing of
the loudspeakers, try reversing the connections (RED & BLACK) to ONE of the loudspeakers, and
play a recording which has plenty of deep bass operating both loudspeakers simultaneously with
the stereo amplier switched to »mono«. The correct polarity is indicated by rm full bass, when
incorrect, the bass will be noticeably much weaker.
Service
No routine attention is required to the working parts of the loudspeakers and being very reliable
Eltax loudspeakers rarely require service. Any service problems should in the î‚¿rst instance be
referred to your dealer.
Set Up of Speaker System for your Home Theatre
A surround sound system, as a minimum, requires 5-7 loudspeakers. It is important to position
them carefully. Thus we recommend that you work with the arrangement of the speakers in your
system, perhaps our idea of placing the system initially may not suit the way in which your furniture
is arranged.(see page 10)


Product specificaties

Merk: Eltax
Categorie: Luidspreker
Model: Shine 5-pack

Heb je hulp nodig?

Als je hulp nodig hebt met Eltax Shine 5-pack stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Luidspreker Eltax

Handleiding Luidspreker

Nieuwste handleidingen voor Luidspreker