Elite Screens ZSP-TR01 Handleiding
Elite Screens
Controller
ZSP-TR01
Bekijk gratis de handleiding van Elite Screens ZSP-TR01 (3 pagina’s), behorend tot de categorie Controller. Deze gids werd als nuttig beoordeeld door 9 mensen en kreeg gemiddeld 3.9 sterren uit 5 reviews. Heb je een vraag over Elite Screens ZSP-TR01 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/3
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
Wireless RF Projector Trigger Controller
Part# ZSP-TR01
User Guide
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
SPECIFICATIONS
1. Size and Weight: W x H x D: 4.8”x2”x0.7”, Weight: 0.09LBS
2. : 80 feet (25M) Max. Control Distance
Control Type: ASK / FSK
3. 15V Projector Output Support Trigger Voltage: 3－
4. 315Mhz, Power Below 2 milli-watts RF Spec. Frequency: ：
5. : Directions for user
a. Connect the wireless RF trigger controller and the projector as shown below.
b. Use the wireless RF trigger controller to synchronize the screen drop/rise with the
projection s power cycle via remote control according to the version number on ’
your screen. Version number can be located either on the screen’s end cap
sticker or on the outside sticker of the packaging box.
Location of version number
on end cap sticker.
Fig. 1
Location of version number
on packaging box sticker.
Fig. 2
Rev. 042710- JA
www.elitescreens.com info@elitescreens.com
Note: Directions for synchronizing your 5-12V wireless trigger according to the
version number.
Version 1.4 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Push the small button located on the circuit board on the left side of the projection screen
(please note: you may require a small sharp object to achieve this After the light turns on, ). LED
press & hold the button on your Wireless RF Trigger Controller and make sure the LED light on UP
circuit board turns on.
Step 2: Continue to hold the button for an additional 3-4 seconds. After 3-4seconds, your 5- V up 12
Wireless Trigg should er be activated and you’ll be able to control your screen with your projector s ’
power cycle .
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around
20-30 seconds for full off and on cycle each time)
Version 2.0 (5-12V wireless trigger and Elite electric screen must be the same version)
Step 1: Make sure to unplug your screen from the power outlet
Step 2: Hold the UP button on your 5-12V wireless trigger
Step 3: While holding the button, plug the screen back to the power outlet UP
Step 4: Wait 5 seconds and then release the button UP
Step 5: Your 5-12V wireless trigger should now be activated with your screen and ready to be used
and able to control your screen with your projector s power cycle. ’
Repeat the steps again if not successful.
Note: Once your RF remote has been activated, th synchronization will be saved even the power e if
is cut off.
Fig. 3
Product specificaties
| Merk: | Elite Screens |
| Categorie: | Controller |
| Model: | ZSP-TR01 |
Heb je hulp nodig?
Als je hulp nodig hebt met Elite Screens ZSP-TR01 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Controller Elite Screens
27 Juli 2023
Handleiding Controller
- Amazon
- Nedis
- Radial Engineering
- Polsen
- Canyon
- Cisco
- Sweex
- Movistar
- Big Ben
- Media-tech
- SPL
- Atlas Sound
- Kohler
- BZBGear
- MOZA
Nieuwste handleidingen voor Controller
17 Juni 2025
10 Juni 2025
7 Juni 2025
24 Mei 2025
24 Mei 2025
24 Mei 2025
23 Mei 2025
14 Mei 2025
11 Mei 2025
11 Mei 2025