Elektrobock Pocket Home PH-SP1 Handleiding
Elektrobock
Receiver
Pocket Home PH-SP1
Bekijk gratis de handleiding van Elektrobock Pocket Home PH-SP1 (4 pagina’s), behorend tot de categorie Receiver. Deze gids werd als nuttig beoordeeld door 34 mensen en kreeg gemiddeld 4.3 sterren uit 17.5 reviews. Heb je een vraag over Elektrobock Pocket Home PH-SP1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
Version 11.02
Wireless receiver for control of
electric heating devices
- UNDER THE SWITCH -
PH-SP1
Operating instructions
Control of electric heating systems
Component of the PocketHome®system
Two-way radio communication at 433,92 MHz
The connected electric appliance is switched
according to the required temperature
The control unit PH-BSP is the pilot component
INSTALLATION
The device can only be installed by a person with adequate
qualification! The installation must be executed in
a voltage-free state!
Wiring diagram:
230 V/ 50 Hz
L
N
max.
16 A
L N
FUNCTION BUTTON ( R ) :
SHORT PRESSING (for
about1,5s) -coding.
LONG PRESSING (for about 5s)
-RESET deleting the code from
the memory (the green and red
LEDs flash simultaneously).
PH-SP1 is used for switching the heating device in connection
with the PH-BSP control unit. The big advantage is mounted
directly into the
installation box.
1. Switch off the main circuit breaker.
2. Connect the receiver acc. to the diagram.
3. Switch on the main circuit breaker; the green diode
flashes on the receiver; thus the receiver is ready for
further setting.
4. Shortly press the FUNCTION BUTTON for about
1.5 s (the green and red diode are flashing alternately).
5. On the PH-BSP control unit, press the “Test” button in
the mode to activate the SP ACTIV
switching components (see page 10
of the PH-BSP instructions).
6. If the code has been learned correctly,
the green and red diodes flash
simultaneously.
LED 2LED 1
empty memory, code not learned
code learned
FLASHING ALTERNATELY= code learning mode
FLASHING SIMULTANEOUSLY= code has been learned
SIMULTANEOUS LONG FLASH= code was ERASED
relay switched
ERROR (if no signal is received from the transmitter
within approx. 6 hours, it switches to the 2-min-ON /
8-min-OFF mode). LED flashes only if the relay is on,
i.e. for 2 minutes.
EXPLANATION: LIT UNLIT FLASHING
FUNCTION
ACTIVATION PROCEDURE
INDICATION DIODES
Product specificaties
| Merk: | Elektrobock |
| Categorie: | Receiver |
| Model: | Pocket Home PH-SP1 |
Heb je hulp nodig?
Als je hulp nodig hebt met Elektrobock Pocket Home PH-SP1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Receiver Elektrobock
15 November 2024
19 Juni 2023
20 Mei 2023
8 Mei 2023
8 Mei 2023
18 April 2023
10 Maart 2023
22 Februari 2023
Handleiding Receiver
- Televés
- AER
- Lanzar
- Taramps
- Phonic
- MB Quart
- Audac
- Fostex
- Gefen
- Fosi Audio
- HEOS
- Palmer
- Plantronics
- Hotone
- LEA
Nieuwste handleidingen voor Receiver
17 Juni 2025
17 Juni 2025
17 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025