Elektrobock BT22 Handleiding
Elektrobock
Thermostaat
BT22
Lees hieronder de 📖 handleiding in het Nederlandse voor Elektrobock BT22 (6 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6
MADE IN CZECH REPUBLIC
BPT22 is an ideal solution in places where installation of the thermostat-boiler wiring is too expensive or
totally impossible. It is intended for automatic control of heating systems in family houses and dwelling units
with their own boiler (gas, electric). The big, backlit display on the transmitter enables control of the
thermostat even in the dark. Moreover, it offers intuitive navigation in the selected language (CZ/PL/EN/DE).
The receiver is equipped with a code self-learning system and the E-EPROM memory which saves the code
stored even in the event of voltage failure. BPT22 works with two-way communication at the frequency of
433.92 MHz. The assembly may reach the range of up to 35 m (in built-up area).
• Receiver mains supply of 230 V/ 50 Hz
• Receiver with the CODE SELF-LEARNING
system and E-EPROM memory (saving the
code even at voltage failure)
• Two-wire connection to the boiler
(potential-free contact)
• Indicator LED signalling the states
- mains supply indication
- transmission/ reception of signals
- failure state
- relay switched
Receiver – into the socket
Transmitter
• Big, well-arranged and backlit display
• Intuitive navigation in the selected language
(CZ/PL/EN/DE)
• Preset weekly program
• 6 temperature changes per every day
• Programming by 10 minutes and 0.5 °C
• Programming by days or Mon-Fri, Sat-Sun
and Mon-Sun
• HYSTERESIS selection from 0.1 °C to 6 °C
• Possibility of short-term temperature change
• Manual mode (MANU)
• Permanent shutdown (OFF)
• Holiday mode
• Anti-freeze temperature (3 °C)
• Function for testing the correct connection
(TEST)
• Automatic SUMMER/WINTER time change
• Supply by means of alkaline batteries
2 x 1.5 V/AA
- freely portable
- modern design
- stand for stable setting at the
optimum location
TWO-WAY COMMUNICATION
- guarantees reliability of signal transmission and
enables acquiring of return information
2
RECEIVER CONTROL ELEMENTS
RECEIVER INSTALLATION
CODE LEARNING
- Switch off the main circuit breaker.
- Connect the receiver to the boiler according to the wiring diagram (use the boiler terminals
intended for the room thermostat 2 conductors!).
- Connect the receiver to the mains 230 V / 50 Hz.
- Switch on the main circuit breaker; the green diode lights up on the receiver; the receiver is
ready for operation.
Install the receiver (in internal rooms) as far from big metal objects as possible (at least 0.5 m)
and far from power lines owing to interference of the signal received! It is recommended that the
device is installed by a person with adequate qualifi cation in electrical engineering!
The BPT22 assembly is confi gured and ready to use – to put the receiver and
transmitter in operation, just use the TEST function (see page 5)!
If the receiver memory has, however, been cleared – the red diode is fl ashing – proceed as
follows:
1) Press the receiver’s “FUNCTION BUTTON” for about 1.5 sec; the yellow and red LEDs start
fl ashing alternately; and the receiver is awaiting the code (“learning mode”).
2) Press twice the “ MENU “, button on the receiver (after inserting batteries, see page 3),
choose the CONST mode by turning the“ “ button, and move on to TEST by pressing
the “ “ button several times. Turn the “ “ button, the signal will be sent to the receiver.
The wireless transmission sign “ “ appears shortly on the transmitter; and after establishing
connection, the RFM message is displayed permanently.
3) The code receipt in the receiver is indicated by simultaneous fl ashing of the yellow and red
LEDs; thus the code has been learnt. After the code receipt, the output relay is switched several
times to verify correct function of BPT22.
Indicating LEDs:
GREEN LIT - correct mains connection
YELLOW
YELLOW
YELLOW
YELLOWYELLOW FLASHING - signal transmission
or reception
RED FLASHING - empty E-EPROM memory
RED LIT - FAILURE (if no signal from the transmitter
is received within approx. 6 hours, it switches to the
“2-min-ON / 8-min-OFF” mode)
YELLOW
YELLOW
YELLOW
YELLOWYELLOW+ FLASHING ALTERNATELY - code learning modeRED
YELLOW
YELLOW
YELLOW
YELLOWYELLOW+ FLASHING SIMULTANEOUSLY - code has been RED
learned
YELLOW
YELLOW
YELLOW
YELLOWYELLOW+ LIT SIMULTANEOUSLY - memory clearing modeRED
ORANGE LIT - relay 1 closed
FUNCTION BUTTON
- SHORT PRESS
(for approx. 1,5 s)
CODE LEARNING mode
- LONG PRESS
(for approx. 5 s)
RESET (memory clearing)
boiler output
(potential-free
switching
contact)
power supply
230 V/50 Hz
through-way
socket for
connection of
another device
Switching functions:
AUT - working according to the program
ZAP - switched on permanently VYP - switched off permanently
BOILER
2
Wiring diagram:
3
alkaline battery
1.5V/AA
alkaline battery
1.5V/AA
1
2
3
4
5
6 7 8 9 10 11
12
13
14
15
16
Fig.1 Fig.3Fig.2
BATTERY REPLACEMENT
As soon as the “ “ sign appears on the display, you must replace
the batteries.
1) Remove the control part from the bottom cover of the device (Fig. 1).
2) Replace the batteries. Heed the correct polarity indicated in the
battery compartment (Fig. 2). After you remove the batteries, the
thermostat keeps all settings in the memory for only about 20 s.
Always use alkaline pencil-type batteries 2 x1,5 V type AA!
After replacing the batteries, perform the TEST (see page 5)!
Recommendation: Check the batteries before every heating season!
Dispose of old batteries in conformity with regulations
on hazardous waste handling!
TRANSMITTER DESCRIPTION
TRANSMITTER INSTALLATION
The transmitter must be installed as far from interference sources (TV, PC, etc.) as possible; it
must not be placed on a metal base. Pay attention to the thermal characteristics of the given place at
installation.
- Lift off the back cover of the transmitter acc. to Fig. 1.
- Remove the protective paper from the batteries; the transmitter will be fully operational (batteries
are included in the BPT22 packaging).
- Snap back the back cover.
- The transmitter is freely portable and can be located, for instance, on the table. We recommend
you to use the delivered table stand (installation acc. to Fig. 3).
- If installed on the wall, no power lines must run around the thermostat!
DISPLAY DESCRIPTION
1, Current day (in the Prog
mode, selection of the
number of days to be
programmed)
2, Heating on indication
3, Current room temp.
4, CLOC mode indication
(current day and time
setting)
5, Program (PROG) and
constant (CONST)
setting modes (page 5)
6, Automatic mode (page 4)
7, Manual mode (page 4)
8, Permanent switch-off
(page 4)
9, Holiday mode (page 4)
10, Signal transmission
indication
11, Signal transmission
ERROR
12, Wireless mode indication
13, Current time
14, Current date / required
temperature
15, Status line, dynamically
changing according to
the running process
16, Low battery indication
Product specificaties
| Merk: | Elektrobock |
| Categorie: | Thermostaat |
| Model: | BT22 |
Heb je hulp nodig?
Als je hulp nodig hebt met Elektrobock BT22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Thermostaat Elektrobock
12 Maart 2024
11 September 2023
11 September 2023
11 September 2023
11 September 2023
11 September 2023
11 September 2023
24 Juni 2023
6 Juni 2023
13 Mei 2023
Handleiding Thermostaat
- Thermostaat Bosch
- Thermostaat Panasonic
- Thermostaat Bticino
- Thermostaat AEG
- Thermostaat ATAG
- Thermostaat Honeywell
- Thermostaat Junkers
- Thermostaat Nefit
- Thermostaat Remeha
- Thermostaat Siemens
- Thermostaat Vaillant
- Thermostaat ACV
- Thermostaat Agpo Ferroli
- Thermostaat Alecto
- Thermostaat Amfra
- Thermostaat Arnold Rak
- Thermostaat AVM
- Thermostaat AWB
- Thermostaat Basetech
- Thermostaat Berker
- Thermostaat Boneco
- Thermostaat Brennenstuhl
- Thermostaat Brink
- Thermostaat Bryant
- Thermostaat Buderus
- Thermostaat Bulex
- Thermostaat Daikin
- Thermostaat Danfoss
- Thermostaat De Dietrich
- Thermostaat Devi
- Thermostaat Devolo
- Thermostaat Dimplex
- Thermostaat Drayton
- Thermostaat Drayton Erie
- Thermostaat Easy Timer
- Thermostaat EasyTemp
- Thermostaat EBERLE
- Thermostaat Econo-Heat
- Thermostaat Elco
- Thermostaat Elgato
- Thermostaat Eliwell
- Thermostaat Elro
- Thermostaat ELV
- Thermostaat Emerson
- Thermostaat Emmeti
- Thermostaat Eneco
- Thermostaat EQ-3
- Thermostaat Eqiva
- Thermostaat Essent
- Thermostaat Etherma
- Thermostaat Eurotronic
- Thermostaat Extraflame
- Thermostaat Ferroli
- Thermostaat Finder
- Thermostaat GE
- Thermostaat Gira
- Thermostaat Go Green
- Thermostaat Google
- Thermostaat Grasslin
- Thermostaat Grohe
- Thermostaat Hager
- Thermostaat Helios (Amfra)
- Thermostaat HomeMatic
- Thermostaat Hornbach
- Thermostaat HQ
- Thermostaat Hugo Muller
- Thermostaat Hunter
- Thermostaat ICY
- Thermostaat Intergas
- Thermostaat IR-V
- Thermostaat Itho
- Thermostaat Itho-Daalderop
- Thermostaat Landis Gyr
- Thermostaat Levica
- Thermostaat Lowes
- Thermostaat Magnum
- Thermostaat Max
- Thermostaat Muller
- Thermostaat Nest
- Thermostaat Netatmo
- Thermostaat Niko
- Thermostaat Nobo
- Thermostaat Noma
- Thermostaat Perel
- Thermostaat Plieger
- Thermostaat Plugwise
- Thermostaat Profile
- Thermostaat Radson
- Thermostaat REMKO
- Thermostaat Renkforce
- Thermostaat RWE
- Thermostaat Salus
- Thermostaat Saunier Duval
- Thermostaat Schneider
- Thermostaat Silvercrest
- Thermostaat Somfy
- Thermostaat Stiebel Eltron
- Thermostaat Sygonix
- Thermostaat Tado
- Thermostaat Taurus
- Thermostaat Techno Line
- Thermostaat Technoline
- Thermostaat Tesla
- Thermostaat TFA
- Thermostaat Theben
- Thermostaat THERMAFLEX
- Thermostaat Thermy
- Thermostaat TP Link
- Thermostaat Trotec
- Thermostaat Truma
- Thermostaat UPM
- Thermostaat Vasco
- Thermostaat VDH
- Thermostaat Velleman
- Thermostaat Viessmann
- Thermostaat Wachendorff
- Thermostaat Watts
- Thermostaat Webasto
- Thermostaat Westfalia
- Thermostaat Wolf
- Thermostaat Worcester-Bosch
- Thermostaat Xavax
- Thermostaat Z-Wave
- Thermostaat Zehnder
- Thermostaat Johnson Control
- Thermostaat Jung
- Thermostaat Oertli
- Thermostaat OJ ELECTRONICS
- Thermostaat Orbis
- Thermostaat Oregon Scientific
- Thermostaat Otio
- Thermostaat Schwaiger
- Thermostaat Fenix
- Thermostaat Conrad
- Thermostaat Corberó
- Thermostaat EMOS
- Thermostaat King
- Thermostaat Cotech
- Thermostaat Hive
- Thermostaat Kemot
- Thermostaat Coati
- Thermostaat Nexa
- Thermostaat SPC
- Thermostaat Baxi
- Thermostaat Aube
- Thermostaat Carrier
- Thermostaat Cepra
- Thermostaat Delta Dore
- Thermostaat ELKO
- Thermostaat Fantini Cosmi
- Thermostaat Heatmiser
- Thermostaat Heimeier
- Thermostaat Horstmann
- Thermostaat IMIT
- Thermostaat Oventrop
- Thermostaat Seitron
- Thermostaat TrickleStar
- Thermostaat Tylö
- Thermostaat Vemer
- Thermostaat Warmup
- Thermostaat Fibaro
- Thermostaat Energenie
- Thermostaat Mikoterm
- Thermostaat Ariston Thermo
- Thermostaat Carel
- Thermostaat Busch-Jaeger
- Thermostaat EVE
- Thermostaat Optima
- Thermostaat Frico
- Thermostaat EQ3
- Thermostaat Homematic IP
- Thermostaat Computherm
- Thermostaat Wattio
- Thermostaat Crestron
- Thermostaat POER
- Thermostaat Heatit
- Thermostaat 2Heat
- Thermostaat Veria
- Thermostaat ThermoSmart
- Thermostaat Yokis
- Thermostaat Vimar
- Thermostaat PECO
- Thermostaat H-Tronic
- Thermostaat Intertechno
- Thermostaat Tru Components
- Thermostaat Emko
- Thermostaat Innogy
- Thermostaat Wallair
- Thermostaat Maico
- Thermostaat Ouellet
- Thermostaat ChiliTec
- Thermostaat Tellur
- Thermostaat Jumo
- Thermostaat Qubino
- Thermostaat STI
- Thermostaat Gewiss
- Thermostaat Sinustec
- Thermostaat Rose LM
Nieuwste handleidingen voor Thermostaat
20 April 2024
16 April 2024
13 April 2024
8 April 2024
20 Maart 2024
20 Maart 2024
20 Maart 2024
17 Maart 2024
14 Maart 2024
4 Maart 2024