Electrolux EFP663 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Electrolux EFP663 (10 pagina's) in de categorie Afzuigkap. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
INSTRUCTIONS FOR USE
GEBRAUCHSANWEISUNG
INSTRUCTIONS POUR L'EMPLOI
ISTRUZIONI PER L'USO
INSTRUCCIONES PARA EL USO
GEBRUIKSAANWIJZING
WARNING
-----------------------------------------------------------
The distance between the supporting surface
for the cooking vessels on the hob and the lower
part of the hood must be at least 65 cm. If the
instructions for installation for the hob specify a
greater distance, this has to be taken into
account.
The air collected must not be conveyed into a
duct used to blow off smokes from appliances
fed with an energy other than electricity (central
heating systems, thermosiphons, water-
heaters, etc.).
Comply with the official instructions provided by
the competent authorities in merit when installing
the disposal duct. In addition, exhaust air should
not be discharged into a wall cavity, unless the
cavity is designed for that purpose.
The room must be well aerated in case a hood
and some other heat equipment fed with an
energy other than electricity (gas, oil, coal
heaters, etc) operate at the same time. In fact
the intake hood, disposing of air, could create a
vacuum in the room. The vacuum should not
exceed 0,04mbar. This prevents the gas
exhausted by the heat source from being intaken
again. It is therefore advisable to ensure the
room contains air taps able to ensure a steady
flow of fresh air.
Check the data label inside the appliance;
if the symbol ( ) is printed, read the
following: this appliance has such
technical particulars that it belongs to class
II insulation, therefore it must not be
earthed.
The following warning is valid in the United
Kingdom only: in case your cable is not furnished
with a plug, read the following instructions; as
the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
– the wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black;
– the wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.
– terminal of a three-pin plug.
Check the data label inside the appliance;
English
if the symbol ( ) is NOT printed, read the
following: ATTENTION: This appliance
must be grounded. When making the electrical
connections, check that the current socket has
a ground connection.
The following warning is valid in the United
Kingdom only: as the colours of the wires in the
mains lead of this appliance may not correspond
with the coloured markings identifying the
terminals in your plug, proceed as follows:
– the wire which is coloured green and yellow
must be connected to the terminal in the plug
which is marked with the letter E or by the earth
symbol [ ], or coloured green or green and
yellow;
– the wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black;
– the wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.
When making the electrical connections, check
that the voltage values correspond to those
indicated on the data plate inside the appliance
itself. In case your appliance is not furnished
with a non separating flexible cable and has no
plug, or has not got any other device ensuring
omnipolar disconnection from the electricity
main, with a contact opening distance of at least
3 mm, such separating device ensuring
disconnection from the main must be included
in the fixed installation. If your unit features a
power lead and plug, position this so the plug is
accessible.
Always switch off the electricity supply before
carrying out any cleaning or servicing operations
on the appliance.
USE
-----------------------------------------------------------
Avoid using materials which could cause spurts
of flame (flambées) near the appliance.
When frying, take particular care to prevent oil
and grease from catching fire. Already used oil
is especially dangerous in this respect. Do not
use uncovered electric grates.
To avoid possible risks of fire always comply with
the indicated instructions when cleaning anti-
grease grille and when removing grease deposits
from the appliance.
MAINTENANCE
-----------------------------------------------------------
Thorough servicing guarantees correct and
long-lasting operation.
Particular care must be paid to the grease grille
which must be periodically cleaned in relation to
use (at least once every two months). Remove
the grease grille and wash them either by hand
or in the dishwasher using neutral detergent.
Any fat deposits should be removed from the
appliance periodically depending on amount of
use (at least every 2 months). Avoid using abra-
sive or corrosive products. To clean painted
appliances on the outside, use a cloth dipped in
lukewarm water and neutral detergent. To clean
steel, copper or brass appliances on the outside,
it is always best to use specific products, following
the instructions on the products themselves. To
clean the inside of the appliance, use a cloth (or
brush) dipped in denatured ethyl alcohol.
DESCRIPTION
-----------------------------------------------------------
The appliance can be used in both the filtering and
ducting version.
In the Filtering version (Fig. 1), the air and va-
pours conveyed by the appliance are depurated
by charcoal filter(s) and recirculated around the
room. ATTENTION: Using the hood as a filtering
one it is necessary to use the charcoal filter(s) that
purifies the air sent back into the room.
In the Ducting version (Fig. 2), cooking vapours
and odours are conveyed straight outside by a
disposal duct which passes through the wall/ceil-
ing. Use of charcoal filter is therefore unneces-
sary.
According to the model you have bought, the ap-
pliance can include 1 or 2 motors. In the I motor
version the flange for the air to be exhausted has
not got a central position, but it is slightly on the left.
INSTALLATION
-----------------------------------------------------------
Before assembling, in order to manoeuvre the
appliance more easily, take off the grease grille
(Fig. 3): pull the front of the grille upwards; desinsert
the back from its seat.
IMPORTANT: So as not to damage your
product, during installation USE ONLY THE
SCREWS PROVIDED. Make sure these are used
as shown in the following instructions.
To compensate possible depth voids between
the appliance and the wall, a plastic SPACING
BAR to be fixed at the back of the appliance by
means of the three screws A is included (Fig.4).
The 3 screws A to be used are contained in the
accessory bag attached to the plastic spacing
bar. Cut the spacing bar according to the
distance to be adjusted.
Assembly under a pensile cupboard
The following operations are essential for as-
sembly:
–Install the wiring system
–Prepare the air venting hole if your appliance
is to be installed in the Ducting version.
Fixation as indicated in Fig. 5:
Using the relative template make the 4 neces-
sary fixing holes in the bottom of the cup-
board and cut the air venting hole.
Move the hood close to the bottom of the wall
unit and then connect the two units by means
of the 4 self-tapping screws supplied together
with the appliance.
Fixation with brackets as in Fig. 6 (optional):
Take the two brackets (S) out of the accessory
bag together with the 8 screws provided. Fit
the brackets to the wall unit being careful to
position these correctly; for this operation
use the 4 longer screws. At this point, secure
the appliance to the brackets using the 4
shorter screws.
Ducting version: connect the flange of the hood
with the air venting hole made previously in the wall/
ceiling by means of an adequate tube. Make the
electrical connection of the hood by means of the
power supply cable. Assemble the grease grille
with the hood, inserting it obliquely (making the
front side go upwards).
Filtering version: connect a proper pipe to the
flange of the hood so that the air is sent outside the
pensile and sent back into the room. Make the
electrical connection of the hood by means of the
power supply cable. Set the charcoal filter inside
the grease grille blocking it by means of the 2
supplied metal wires (F), as indicated in Fig. 3.
Assemble the grease grille with the hood, inserting
it obliquely (making the front side go upwards).
OPERATION
-----------------------------------------------------------
Controls (Fig. 7):
A = ON/OFF 1st speed switch
B = II speed switch
C = III speed switch
The motor is automatically ON or OFF by
opening/closing the truck (unless switch A is
on 0). Opening the truck the motor works
according to last speed registered.
D = Light switch:position A (automatic), the light
are automatically regulated ON or OFF by
the opening/closing of the truck. Position M


Product specificaties

Merk: Electrolux
Categorie: Afzuigkap
Model: EFP663

Heb je hulp nodig?

Als je hulp nodig hebt met Electrolux EFP663 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afzuigkap Electrolux

Handleiding Afzuigkap

Nieuwste handleidingen voor Afzuigkap