Electro-Voice ND66 Handleiding
Electro-Voice
Microfoon
ND66
Bekijk gratis de handleiding van Electro-Voice ND66 (4 pagina’s), behorend tot de categorie Microfoon. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 3.9 sterren uit 1.5 reviews. Heb je een vraag over Electro-Voice ND66 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
Electro-Voice | ND66
ND66
▪Premium small diaphragm condenser element
▪Clean, crisp, and detailed condenser sound
▪Easy mic placement with locking rotating head
▪Selectable -10dB and -20dB pads
▪Selectable 75Hz and 150Hz high pass filters
The Electro-Voice ND66 is a robust, high-performance
small diaphragm condenser instrument microphone.
The ND66 contains a self-biased small diaphragm
condenser element which is vividly responsive to the
complex dynamic nature of percussive and stringed
instruments, delivering a clean, crisp and detailed
sound.
With the ND66 exclusive locking rotating head, achieve
ideal mic placement in virtually any situation by merely
pushing a button, rotating the head into position, then
releasing the button to lock the head's position.
ND66 contains selectable -10 and -20dB pads which
provide the necessary gain reduction to prevent the
mic element from overloading when micing very loud
or high-transient sound sources.
ND66 contains selectable high pass filters which are
strategically chosen at 75Hz and 150Hz to eliminate
bothersome low frequencies from the signal path.
Technical specifications
Element Type: Self-biased Condenser
Frequency Response, Free
Field:
50Hz to 20kHz
Polar Pattern: Cardioid
Sensitivity, Open Circuit
Voltage @ 1 kHz::
10 mV / Pascal
Maximum SPL: 146 dB SPL, 0dB Pad
Self Noise: 20 dB SPL “A” weighted (0dB=20
micropascals)
Dynamic Range: 126 dB
Signal-to-Noise Ratio: 74 dB (@ 94 dB SPL)
Polarity: Pin 2 positive, reference to pin 3 with
positive pressure on diaphragm
Power Requirements: Phantom Supply Requirement: 48
VDC
Impedance: 200 ohms
Microphone Connector: 3-pin, XLR-type
Finish: Black polyurethane paint
Material: Zinc die cast
Dimensions, Length:
Diameter:
5.63 in (143 mm)
0.83 in (21 mm)
Net Weight: 6.30 oz (179 g)
Shipping Weight: 16.4 oz (465 g)
Accessories Included: (1) Gig bag, (1) stand clip, and (1)
Euro thread adapter
Frequency Response:
-10
20 50
0 dB
+10
500
FREQUENCY IN HERTZ
100 1K 5K 10K 20K
1 m
2.5 cm
5 cm
Frequency Response, Close
-10
20 50
0 dB
+10
500
FREQUENCY IN HERTZ
100 1K 5K 10K 20K
HP 75 Hz
HP 150 Hz
Flat
Frequency Response, Hi-Pass
Dimensions:
143mm
5.63 in
[ 21mm ]
.83 in
ND66
-20
-10
0
Unlock
Button
Polar Response:
System overview
Using the rotating head
The ND66 head will rotate up to 90° with seven
positive locking positions within its rotation range.
!
Caution!
Attempting to rotate the head while the un-
locking button is not pushed may result in
damage to the microphone.
To , do the following:
rotate the head
rotate the head
rotate the head
rotate the headrotate the head
1. Push and hold the unlocking button to unlock the
head.
-20
-10
0
Unlock
Button
2. While holding the unlock button down, rotate the
head to the desired position.
3. Release the unlock button and gently rotate the head
to the nearest positive locking position.
The lock should click into place.
Using the pads
The ND66 head contains selectable attenuators (pads)
which affect the output level of the microphone
capsule feeding the mic’s built-in preamp. The proper
setting will help prevent overloading the built-in
preamp when micing very loud or high-transient sound
sources.
2
| ND66
The center position (marked 0) applies zero
attenuation before the mic’s preamp.
The left-hand position (marked -10) applies
10dB of attenuation before the mic’s built-in
preamp.
The right-hand position (market -20) applies
20dB of attenuation before the mic’s built-in
preamp.
-20
-10
0
Pad
0, -10dB,
-20dB
Using the hi-pass filters
The ND66 contains a 3-position sliding switch whose
selected position will engage high-pass filter settings.
Adjusting the filter setting requires a small flat head
screwdriver (or some other means of sliding the
switch) using the switch’s slot as a leverage point.
With the slot in the sliding switch in the
center position (as shown), the filter is flat
and there is no roll-off applied.
Slot
Sliding the slot upwards revealing 75 (as
shown) engages a 12 dB per octave roll-off
at 75 Hz.
75
High
Pass
75 Hz
Sliding the slot downwards revealing 150 (as
shown) engages a 12 dB per octave roll-off
at 150 Hz.
150
High
Pass
150 Hz
Parts included
Qty. Item
1 Microphone
1 WSND-1 foam windscreen
1 Gig bag
1 Stand clip
1 Euro thread adapter
1 Engineering data sheet
1 Warranty and Product Documentation Information card
Ordering information
ND66
Condenser cardioid instrument microphone, black
Order number ND66
SAND-1
Stand adapter, black
Order number SAND-1
WSND-1
Replacement foam windscreen for ND66, black
Order number WSND-1
ND66RING
Replacement transition ring between head and body,
silver
Order number ND66RING
Accessories
DRC-2
Drum rim clamp, black
Order number DRC-2
3 | ND66
Product specificaties
| Merk: | Electro-Voice |
| Categorie: | Microfoon |
| Model: | ND66 |
Heb je hulp nodig?
Als je hulp nodig hebt met Electro-Voice ND66 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Microfoon Electro-Voice
27 April 2025
27 April 2025
27 April 2025
15 November 2024
5 November 2024
27 Mei 2023
25 April 2023
23 April 2023
23 April 2023
22 April 2023
Handleiding Microfoon
- ZaxSound
- Scope Labs
- Joy-it
- Vonyx
- IMG Stageline
- Rythflo
- Movo
- Lexibook
- AmpliVox
- Razer
- Bontempi
- Warm Audio
- Ibanez
- Glemm
- Pixel
Nieuwste handleidingen voor Microfoon
17 Juni 2025
17 Juni 2025
16 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025