Edifier MR3 Handleiding

Bekijk gratis de handleiding van Edifier MR3 (7 pagina’s), behorend tot de categorie Speaker. Deze gids werd als nuttig beoordeeld door 71 mensen en kreeg gemiddeld 4.5 sterren uit 5 reviews. Heb je een vraag over Edifier MR3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

2. What’s in the box?

Note:

•Images are for illustrative purpose only and may dier from the actual product.

•For the need of technical improvement and system upgrade, information and

specications contained herein may be slightly dierent from actual product. If

any dierence is found, the actual product prevails.

7. Bluetooth connection

4. Mode switch

9. Acoustic tuning

8. Multipoint connection

10. Specications

11. Troubleshooting

Total output power (RMS): 18W+18W (DRC on)

Frequency response: 52Hz-40kHz

Declaration for EU

Frequency Band: 2.402GHz ~ 2.480GHz

RF Power Output: ≤13 dBm (EIRP)

There is no restriction of use.

Quick start guide

Important safety instructions

3.5mm to 3.5mm audio cable

Power cable

3.5mm to RCA audio cable

Speaker connecting cable

Manual

Cannot connect to your Bluetooth device

•Make sure that the distance between this product and your Bluetooth device

is less than 10 meters and there are no obstacles between them.

•Make sure that no device is connected to this product via Bluetooth.

•Make sure that this product is in Bluetooth pairing mode. If not, manually

switch it to this mode.

•Resta this product, enable Bluetooth function on your Bluetooth device,

and then t again.

•Reset this product to facto settings and t again.

No power

•Make sure that the power cable is properly connected.

•Make sure that the power supply is not disconnected.

No sound

•Make sure that this product and your device is properly connected.

•Make sure that the correct audio input source is selected.

•Make sure that the playback is not paused.

•Increase the volume of this product and your device.

Noise coming from speakers

EDIFIER speakers generate little noise, while the background noise of some

audio devices are too high. Please unplug audio cables and turn the volume

up. If no sound can be heard at 1 meter away from the speaker, there is no

problem with this product.

To learn more about EDIFIER, please visit www.edier.com

For EDIFIER warranty queries, please visit the relevant count page on

www.edier.com and review the section titled Warranty Terms.

USA and Canada: seice@edier.ca

South America: Please visit www.edier.com (English) or

www.edierla.com (Spanish/Pouguese) for local contact information.

With this app, you can

•control play from the Bluetooth

source device,

•control the master volume,

•select sound eects or customize EQs,

•peorm acoustic tuning,

•upgrade the rmware, and

•more functions.

Download EDIFIER ConneX app

1. With your sma device, scan the QR code on the quick sta guide or the

packaging.

•You can also search for "EDIFIER ConneX" in Apple App Store (iOS devices) or

Google Play (Android devices).

2. Download and install the app.

How to use this app

1. Connect your sma device with the speaker via Bluetooth.

2. In Bluetooth mode, open EDIFIER ConneX App on your sma device.

3. Tap the menu for settings and playback control.

EDIFIER ConneX app

3. Cable connection

Note:

•Power input: 100-240V~ 50/60Hz 300mA

•This plug type is meant for illustrative purpose only.

•All audio inputs including Bluetooth connection can be used in parallel.

•The speaker will be muted when you connect your headphone to the " " po.

You can control the headphone volume with the volume knob on the speaker.

EN

1. EDIFIER ConneX app

Press and hold the " " knob to switch the speaker between work mode and

standby mode.

1. Press the " " button on the speaker. The indicator will blink.

2. On your device, select "EDIFIER MR3" in its Bluetooth device list to connect.

The indicator will be steadily lit when the connection is established.

•The speaker will automatically reconnect to the last-connected Bluetooth

device after it is switched to work mode. If not, press the " " button on the

speaker to activate the re-connection.

•To disconnect from the current Bluetooth device, press and hold the " " button

on the speaker for 1.5 seconds.

By the speaker knobs

"High" knob: Turn the knob to boost or cut high frequencies above 10kHz by ±6dB.

"Low" knob: Turn the knob to boost or cut low frequencies around 125Hz by ±6dB.

By the EDIFIER ConneX App

Low cuto: Attenuate frequencies lower than the specied frequency (20-100Hz)

at a selected slope (6, 12, 18, or 24dB/octave).

Acoustic space: Select a gain level to compensate for the bass boost, which varies

with speaker placement, 0dB for being in the middle of the room and -4dB for

being in the corner. The closer the speaker is to a wall or corner, the smaller the

value is to be set.

Desktop control: When the speaker is placed on a desktop or an object is placed

in front of it, there may be an apparent increase in the decibel level at ceain

frequencies. Enable the feature to mitigate this eect.

This speaker suppos the simultaneous connection of two Bluetooth devices.

1. Connect the rst Bluetooth device to the speaker.

2. Press and hold the " " button on the speaker for 1.5 seconds.

3. On the second Bluetooth device, select "EDIFIER MR3" in its Bluetooth device

list to connect.

4. On the rst Bluetooth device, select "EDIFIER MR3" in its Bluetooth device list

to reconnect.

•Pause or stop playback on the current Bluetooth device before streaming audio

from the second one.

Note:

•Pin code for connection is "0000" if needed.

•To enjoy all Bluetooth functions of this product, make sure that your audio

source device suppos A2DP and AVRCP proles.

•If no device is connected in 3 minutes, the speaker will switch to Bluetooth

hidden mode. In this mode, (1) new devices cannot nd the speaker, but (2)

for a device that exists in the pairing record of this speaker, you can select

"EDIFIER MR3" from its Bluetooth device list to reconnect. To exit from

Bluetooth hidden mode, press the " " button on the speaker.

5. Control

6. Indicator status

Note: Volume sync is not suppoed. To adjust the volume, adjust on the speaker

and your device separately.

Button/KnobMode

Action

Work modePress to switch sound eects.

Work modeRotate clockwise to increase volume.

Work mode

Rotate counterclockwise to decrease

volume.

Bluetooth device

connected

Press and hold to disconnect the

current Bluetooth device and switch

the speaker to Bluetooth pairing

mode.

Bluetooth hidden

mode

Press to exit Bluetooth hidden mode

and enter Bluetooth pairing mode.

Indicator statusSpeaker status

Solid redMonitor sound eect

Solid greenMusic sound eect

Solid whiteCustomized sound eect

BlinkingBluetooth pairing mode

Blinking and then in solidBluetooth device connected

Blinking in red and greenUpgrading the rmware

Studio Monitor

MR3

Active speakerPassive speaker

*

1.5s

1.5s

ONOFF

Bluetooth

Settings

EDIFIER MR3

DEVICES

Bluetooth

2:12

1

2

-6dB+6dB

125Hz

Low

-6dB+6dB

0

-6dB+6dB

10kHz

High

-6dB+6dB

0

14:10

14:10

Product specificaties