EBERLE INSTAT+ 2R Handleiding

Bekijk gratis de handleiding van EBERLE INSTAT+ 2R (2 pagina’s), behorend tot de categorie Thermostaten. Deze gids werd als nuttig beoordeeld door 19 mensen en kreeg gemiddeld 4.0 sterren uit 2 reviews. Heb je een vraag over EBERLE INSTAT+ 2R of wil je andere gebruikers van dit product iets vragen? Stel een vraag

User and installation guide

+2R

Room Temperature Controller

468931003114-3

06490047001 Iss G



I. User Guide

Operation (Overview)

1. Principle of function

INSTAT

+

the programmable room thermostat allows you to set time periods (up to 6 per

day) and temperatures to suit your own lifestyle. Once fully installed and powered the

device will automatically set the correct time and in auto mode will control your heating

system according to pre-set program 1 (see 7.). The temperature is controlled by sensing

air temperature, switching on the heating when the air temperature falls below the ther-

mostat setting and switching it off once this set temperature has been reached.

NOTE:

The adjusted values (while programming) will be accepted automatically after ~5 sec.

2. How to insert batteries (2 AA 1,5V Alkaline)

3.Automatic mode (AUTO)

In this mode, the room temperature is automatically controlled according to the pre-set

program. The pointer indicating the mode is set to AUTO. The number at the bottom right

indicates the program event during the day. (Fig. 1)

4.How to change the temperature for a short period of time

(override)

When in AUTO mode, you can override the existing temperature setting for a short period

of time.

Press the +–or buttons to change the temperature setting.

While in temperature override the pointer indicates both AUTO and MAN (Fig. 2).

When the next programmed time/temperature event is reached, the device will revert to

the AUTO mode.

5. How to set a constant room temperature (manual operation)

In this mode, a constant temperature can be set, and the pre-set program is ignored.

The temperature last selected is chosen as the initial temperature.

How to activate this mode

Press the <button until the pointer indicates MAN (Fig. 3).

Set the temperatureby pressing the +/ –button

Exit the mode

by pressing the >button

6.How to set the room temperature for a set time

(holiday/party mode)

In this mode, the temperature can be set for periods of time ranging from a few hours up

to 199 days, e.g. when you are away from home for longer periods of time (holidays).

The remaining hours/days are shown. Time periods between 1 hour and 23 hours and 1

day and 199 days can be set.

How to activate this mode

Press the <button until the pointer indicates the suitcase icon (Fig. 4)

Set the temperatureby pressing the +/ –button

Select the timeby pressing the <button

Set the time by pressing the +/ –button

Once you have set your time period, the time will flash for 10 seconds and then start the

holiday/party period.

To exit this mode, press <or >.

When hours have been set, the controller will return to AUTO mode once the set hours

have passed.

When days have been set, the controller will return to AUTO mode at midnight of the last

day.

Note:the current day (today) must be included in the setting.

e.g. 1 day is set; the controller returns to AUTO today at midnight.

Days

Temperature

see note below

+ or – buttons

for setting

values e.g.

temperature

Pointer indicates

the day of the week

Flame icon

(heating on)

Time

Pointer indicates

the current mode

Modes:

automatic, manual,

holiday, day, program

(see 3., 4., 5., 6.)

Moves the pointer

to the left e.g. to

select the mode

Moves the pointer

to the right e.g. to

select the mode

Setting the clock

(see 11.)

Time/Temperature

Program events 1…6

in sequence morning,

midday and night (see 7.)

Battery run low

(see 10.)

Note: Temperature displayed is actual room temperature. After pressing + or – button the set

temperature is displayed. Once adjustment is complete and after 5 seconds display will show actual

room temperature. Days are shown as 1 to 7 (1= Monday to 7= Sunday)

Fig. 1Fig. 2

Fig. 3Fig. 4

7.Pre-set programs

There are 3 pre-set time/temperature programs which are already available in the control-

ler. Pre-set program 1 (as shown below) is the default. Therefore, if pre-set program 1 is the

best program to suit your lifestyle, you do not need to change the time/temperature set-

tings on the device.

To select an other program see 9.3

Program 1 (home during the day)

Monday to Friday

Events123456

Time6:008:3012:0014:0017:0022:00

Temperature °C21,018,021,018,021,015,0

Saturday and Sunday

Events123456

Time7:0010:0012:0014:0017:0023:00

Temperature °C21,018,021,021,021,015,0

Program 2 (home for lunch and on weekends)

Monday to Friday

Events123456

Time6:008:3012:0014:0017:0022:00

Temperature °C21,018,021,018,021,015,0

Saturday and Sunday

Events123456

Time7:0010:0012:0014:0017:0023:00

Temperature °C21,021,021,021,021,015,0

Program 3 (at work all day)

Monday to Friday

Events123456

Time6:008:3012:0014:0017:0022:00

Temperature °C21,018,018,018,021,015,0

Saturday and Sunday

Events123456

Time7:0010:0012:0014:0017:0023:00

Temperature °C21,018,021,021,021,015,0

8.How to adjust the pre-set time/temperature program to suit

personal needs

Select the day functionby pressing the button up to position "Day">

Select the dayby pressing the +/ –button

Set the times for this day

Select the event (1…6)by pressing the >button

Set the timeby pressing the +–/ button

Select the temperatureby pressing the >button

Set the temperatureby pressing the +/ –button

The >button must be pressed to accept a setting.

If you wish to change other events or days, repeat the actions described above. To return

to the auto mode, press the <button.

Note:The last event of the current day can be extended up to the first event of the follo-

wing day.

6:00 h8:00 h10:00 h12:00 h14:00 h16:00 h18:00 h20:00 h22:00 h

°C

22

21

20

19

18

17

16

15

14

Mon – Fri

Sat – Sun

6:00 h8:00 h10:00 h12:00 h14:00 h16:00 h18:00 h20:00 h22:00 h

°C

22

21

20

19

18

17

16

15

14

Mon – Fri

Sat – Sun

6:00 h8:00 h10:00 h12:00 h14:00 h16:00 h18:00 h20:00 h22:00 h

°C

22

21

20

19

18

17

16

15

14

Mon – Fri

Sat – Sun

Table 1 User options

User

optionsDescriptionSelect betweenDefault

1Change 12 h or 24 h clock122424

2Change p1-he manual set point temperature73220

3Change to another pre-set program131

4Change the number of program events per day2, 4 or 66

5Switch on/off automatic daylight savings time/standard time changeONOFFON

6Change temperature display–5.05.00.0

7Restore the built in time temperature programsONOFFOFF

8Switch off the thermostatONOFFOFF

Pay attention to correct

polarity of the batteries!

If operating mode "7 days" is chosen (see installer options, option 1), the days can be

selected as blocks or individual days (Fig. 5 to 8).

The blocks are selected by repeatedly pressing the >button.

Note: To facilitate programming, blocks of days with the same times/temperatures can be

formed before starting.

Fig. 5:Fig. 6:

Monday to Friday as one blockSaturday and Sunday as one block

(working days)(days off)

Fig. 7:Fig 8:

Each day is individual dayMonday to Sunday as one block (all days)

9. How to change user options

The controller offers a number of options that can be changed by the user (see Table 1.).

To activate the menu,in AUTO Mode press the <>and buttons simultaneously for

3 seconds

Select an optionby pressing the <>or button

Change an optionby pressing the +/ –button

Press <or >to accept each change.

To exit the menu, press the <>and buttons simultaneously for 3 seconds.

If no button is pressed within 2 minutes, the device will return to the auto mode.

9.1 How to change from 24h to 12h clock (option 1, table 1)

Shows the time as 24 hours or 12 hours

9.2 How to change the manual set point temperature (option 2, table 1)

Setting the temperature used when the manual mode is selected for the first time, e.g. 20°C

9.3 How to change to another pre-set program (option 3, table 1)

Selection of a pre-set program to be used for programming events (see 7.).

9.4 How to change the number of events per day (option 4, table 1)

2, 4 or 6 time/temperature events can be selected for all days according to individual need

(not used events will be skipped). If there is no need for e.g. 6 events, choosing 4 makes

programming easier.

9.5How to switch on/off the automatic daylight savings time/standard time

change (option 5, table 1)

You can select whether or not you want the time change to be carried out automatically.

If it is not carried out automatically, the time has to be adjusted manually (see 11.).

9.6 How to change the temperature display (option 6, table 1)

The temperature display can be adjusted to individual needs, e.g. 3 = +0,3°; -15 = -1,5°.

9.7 How to restore the built in time temperature programs (option 7, table 1)

Restores the pre-set programs to its original factory settings.

9.8 How to switch off the programmable thermostat (option 8, table 1)

When switched off, the programmable thermostat no longer controls the room tempera-

ture and the room is not heated. The display will show OFF, and the buttons will not functi-

on.

In the installer options (refer to Installation Guide) you can select whether or not frost pro-

tection is to active (heating is called for if the temperature falls below 5°C) when the pro-

grammable thermostat is switched off.

10. How to change the batteries

When the batteries start to run low, the battery icon (refer to Fig. 1) starts to blink. The con-

troller continues to function normally.

After roughly 6 months, the device will cease to function and will permanently display the

battery icon (Fig. 9).

Disposal of batteries according to legislation.

Fig. 9

11. How to change the time, day, month and year

The controller comes with a pre-set clock, which also automatically switches from day light

savings time to standard time.

There should be no need to change these settings. However, should the need arise, the

settings can be changed in the following way.

Activate the clock mode:

Select DAY with button >and then Sunday with button +

With button >move through all 6 time/temperature events (without any modifiaction)

until the pointer indicates the clock icon.

The time will now flash.

Set the time by pressing the +/ –button

Press the >button to select the dayPress the +/ –button to change the setting

Press the >button to select the monthPress the +–/ button to change the setting

Press the >button to select the yearPress the +/ –button to change the setting

Press the >button to return to the AUTO mode

Product specificaties