Durkopp Adler 670 Handleiding
Bekijk gratis de handleiding van Durkopp Adler 670 (140 pagina’s), behorend tot de categorie Naaimachine. Deze gids werd als nuttig beoordeeld door 76 mensen en kreeg gemiddeld 4.8 sterren uit 38.5 reviews. Heb je een vraag over Durkopp Adler 670 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/140
670/680
Service Instructions
All rights reserved.
Property of Dürkopp Adler GmbH and protected by copyright. Any reuse of these contents,
including extracts, is prohibited without the prior written approval of Dürkopp Adler GmbH.
Copyright © Dürkopp Adler GmbH 2021
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Table of contents
Service Instructions 670/680 - 04.0 - 06/2021 1
1 About these instructions ........................................................... 5
1.1 For whom are these instructions intended?.................................. 5
1.2 Representation conventions – symbols and characters ............... 5
1.3 Other documents .......................................................................... 7
1.4 Liability.......................................................................................... 7
2 Safety........................................................................................... 9
2.1 Basic safety instructions ............................................................... 9
2.2 Signal words and symbols used in warnings.............................. 10
3 Working basis ........................................................................... 13
3.1 Order of the settings ................................................................... 13
3.2 Laying the cable guide................................................................ 13
3.3 Gages ......................................................................................... 14
3.4 Removing the covers.................................................................. 16
3.4.1 Access to the underside of the machine..................................... 16
3.4.2 Removing the arm cover ............................................................ 17
3.4.3 Removing the head cover........................................................... 18
3.4.4 Removing the valve cover .......................................................... 19
3.4.5 Removing the rear cover ............................................................ 20
3.5 Flats on shafts ............................................................................ 20
3.6 Locking the machine in place ..................................................... 21
3.7 Setting the handwheel into position............................................ 23
4 Setting the handwheel scale ................................................... 25
5 Positioning the arm shaft......................................................... 26
6 Positioning the toothed belt wheels ....................................... 27
6.1 Positioning the upper toothed belt wheel.................................... 28
6.2 Positioning the lower toothed belt wheel .................................... 29
7 Stitch length adjusting wheels................................................ 30
7.1 Setting the upper stitch length adjusting wheel .......................... 30
7.2 Setting the synchronization of top and bottom feed ................... 32
7.3 Setting the lower stitch length adjusting wheel........................... 33
7.4 Setting the stitch length limit....................................................... 34
7.5 Setting the eccentric for the forward and backward stitches ...... 35
7.6 Setting the feed dog bar ............................................................. 36
7.7 Setting the initial position of the feed gear.................................. 37
8 Needle bar linkage.................................................................... 39
8.1 Aligning the needle bar linkage sideways................................... 39
8.2 Setting transmission lever .......................................................... 41
8.3 Setting the thread lever .............................................................. 42
9 Post bed feed ............................................................................ 43
9.1 Aligning the post bed feed .......................................................... 43
9.2 Setting the feed dog feed movement.......................................... 45
9.3 Setting the feed dog stroke movement....................................... 46
9.4 Setting the feed dog height......................................................... 47
9.5 Setting the compensating weight................................................ 48
9.6 Setting the needle penetration in the feed direction ................... 49
Product specificaties
| Merk: | Durkopp Adler |
| Categorie: | Naaimachine |
| Model: | 670 |
Heb je hulp nodig?
Als je hulp nodig hebt met Durkopp Adler 670 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Naaimachine Durkopp Adler
17 Maart 2025
15 November 2024
15 November 2024
17 Juni 2024
17 Juni 2024
16 April 2024
26 Maart 2024
18 December 2023
20 Maart 2023
20 Maart 2023
Handleiding Naaimachine
- IKEA
- Mio Star
- Bestron
- Blaupunkt
- Weasy
- Kenmore
- Husqvarna-Viking
- Sinbo
- Novamatic
- Aigger
- Crofton
- Hema
- Pfaff
- Siemens
- Janome
Nieuwste handleidingen voor Naaimachine
7 Juli 2025
4 Juli 2025
4 Juli 2025
15 Juni 2025
23 Mei 2025
16 Mei 2025
15 Mei 2025
14 Mei 2025
14 Mei 2025
14 Mei 2025