Draper Access E Handleiding

Bekijk gratis de handleiding van Draper Access E (4 pagina’s), behorend tot de categorie Projectiescherm. Deze gids werd als nuttig beoordeeld door 56 mensen en kreeg gemiddeld 4.3 sterren uit 8 reviews. Heb je een vraag over Draper Access E of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Remove Screws

from both ends

of Screen Housing

Access

Panel Door

pivot on Hinges

OPEN

ACCESS

PANEL

CLOSED

ACCESS PANEL

SCREEN

HOUSING

ATTACACHING BRKETS

Insert pin in top

slot and push up

Rotate bratcke

clockwise to lo ck

braet in placeck

1

2

E BNGAGEMENT RACKET

WITH B DALL ETENT

will snap into Access

Panel Support Braet.ck

ACCESS ANEL P

SUPPORT RACKET B

CENTER of CASE

CENTER of CASE

Bottom Access Panel Installation/Removal

Bottom access panel is secured to the screen housing by two screws (one on

each end), and is held in the closed position by engagement brackets with ball

detents that snap into case support brackets.

To remove the Access Panel:

1 Remove screws from both ends of screen housing (Fig. 4).

2 Pull down on the access panel until the ball detents on the engagement

bracket have disengaged from the support bracket.

3 2 Repeat Step for all brackets along the length of the screen housing.

4The access panel will be free to pivot downward. It will remain attached to

the lower inside edge of the screen housing by several steel hinges.

Caution: For larger sizes Step requires two people to perform safely.5

5 Press up on access panel and pull toward the front of the screen housing to

disengage hinges and remove access panel.

To Remove/Install Support Brackets:

Installation/Operating Instructions

Access Electric Projection Screen by Draper

Copyright © 2016 Draper Inc. Form Access_Inst16 Printed in U.S.A

Hanging Screen

When locating viewing surface and checking clearance for screen operation,

remember surface is centered in the length of the case. Regardless of

mounting method used, the following points apply:

1Mounting brackets are shipped attached to the case. Engage each bracket

with top of housing as shown below and tighten set screws.

2Screen should be positively and securely supported so that vibration or

even abusive pulling on viewing surface will not weaken installation.

Please Note: A Hoisting Bracket is included on each end of the case to

aid in overhead installation of the Access case.

3Installer must insure that fasteners used are of adequate strength and

suitable for the mounting surface chosen. Supporting hardware (chains,

cables,

3

/

8

" rods, etc.) must be essentially vertical.

4Entire bottom of case must be readily accessible after installation is

complete.

5Front, back and top of case must be straight— not forced to warp or bow.

6If case is painted on location, removal of roller/fabric assembly is

recommended prior to painting. If not removed, slot on bottom of case

should be shielded to protect viewing surface from paint splatters/overspray.

7Do not seal unit in ceiling until electrical connections have been made and

screen has been operated successfully.

Electrical Connections

Screen operates on 110-120V, 60 hz., 1.1 amp current draw.

Duty Cycle: ON 28 seconds /OFF 4 minutes.

Junction box is located just above the bottom access panel at left end of

screen (standard, right end may be specified).

Remove the bottom access panel for access to the junction box cover. (See

Bottom Access Panel Removal instructions below). Remove two (2) hex head

screws that secure the cover to the junction box to expose the red, black, and

white pigtail leads and the green ground wire per wiring diagram on page 4.

If optional low voltage control is specified and factory installed, please refer to

wiring diagrams on page 4.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire to connect screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in accordance

with attached wiring diagram, and wiring should comply with national and

local electrical codes.

All operating switches should be “off” before power is connected.

Caution

1Read instructions through completely before proceeding; keep them

for future reference. Follow instructions carefully. Installation contrary to

instructions invalidates warranty. Care in mounting and correct operation

will mean long and satisfactory service from your Draper screen.

2Before removing screen from crate, check for damage and to make sure

all parts are included.

3Allow enough access to remove front cover should fabric become

damaged or should other service be required.

4Screen should be installed level (using a carpenter’s level).

5Nothing should be fastened to screen dowel or viewing surface.

6Operating switch(es) is packed separately in screen carton. Do not

discard with packing material.

7Screen operates on 110-120V, 60 Hz. 1.1 amp current draw.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

If you encounter any difficulties installing or servicing your Access screen, call your

dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-7142.

Suitable for use in environmental air space in accordance with Section

300-22(c) of the National Electrical Code, and Sections 2-128, 12-010(3) and

12-100 of the Canadian Electrical Code, Part 1, CSA C22.1.

Access case

as seen from

below

Bottom flange of

Access housing

Bottom Access Panel Door

Caution: Beware of pinch points at ends of closure

US Patent Nos.

6,137,629; 6,421,175;

6,532,109; 6,816,308;

7,559,707

These instructions are meant as a guide only. They do not imply any responsibility on the

part of the manufacturer for improper installation or faulty workmanship at the jobsite.

1With typical installation, brackets may be angled to meet installation requirements.

Typical

Installation

1

7/8"

ELECTRICAL

CUTOUT

Alternate

Installation

(additional set of

brackets required

but not included)

Figure Figure

Figure

Figure

Figure

Product specificaties