Draper 85634 Handleiding
Draper
Niet gecategoriseerd
85634
Bekijk gratis de handleiding van Draper 85634 (11 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 5 mensen en kreeg gemiddeld 5.0 sterren uit 3 reviews. Heb je een vraag over Draper 85634 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/11
85634
EN
STEEL MESH
CART
Original Instructions
Version 3 – August 2024
– 2 –
For the latest version of this manual, please visit
drapertools.com/manuals
1. Intended Use
This product is designed to transport and move loads
of up to 450kg and is particularly suited to garden
materials. Any other application beyond the conditions
established for use will be considered misuse. Draper
Tools accepts no responsibility for improper use
2. Specication
Stock No. 85634
Part No. GMC/450
Max. load 450kg
Cage capacity 200L
Max. tyre pressure 2.1bar (30psi)
Dimensions
Cage L 1,220 x W 610 x H 274mm
Full L 1,370 x W 630 x H 1,050mm
Net weight 26.6kg
3. Health and Safety Information
Important: Read all the Health and Safety instructions
before attempting to operate, maintain or repair this
product. Failure to follow these instructions may result
in injury or damage to the user or product.
• Observe all standard Health and Safety precautions
when using this cart in an outdoor environment.
• Before every use, inspect the cart for broken, cracked,
loose or corroded parts.
Important: DO NOT use this product if it is damaged
in any way. Contact Draper Tools to discuss repair and
replacement options.
• Wear protective footwear when using this product
under heavy loads.
• DO NOT sit, stand or ride on this cart at any time.
• DO NOT allow children to play with the cart.
• exceed the maximum load specied.DO NOT
• Ensure that the tyres are suitably inated before use.
− DO NOT exceed a tyre pressure of 2.1bar (30psi).
• Distribute the load evenly within the cage.
• Ensure that the load is safely contained within the
cage and unlikely to fall.
− DO NOT load items onto the top edges of
the cage.
• Inspect the intended route and clear any obstructions
before moving the cart under load.
• Take care when moving the cart under load.
− ALWAYS ensure that all parts are secured before
moving the cart.
− DO NOT use the cart on uneven surfaces that
may cause it to tip over.
• The wheels of this product DO NOT lock.
− Ensure that the cart will not roll once positioned
for use.
• Take particular care when using the cart on
sloped surfaces.
• Ensure that the handle is in an upright position
when not in use to avoid a trip hazard.
• ONLY use spare parts supplied by Draper Tools.
4. Identication and Unpacking
4.1 What’s in the Box?
Carefully remove the product from the packaging and
examine it for any signs of damage that may have
occurred during shipment.
Before assembling the product, lay the contents out
and check them against the parts and xings shown.
If any part is damaged or missing, do not attempt to
use the product. Please contact the Draper Helpline;
contact details can be found at the end of this manual.
– 3 –
Parts List
(A) 1 x Cage bed
(E) 1 x Front axle
sub assembly
(I) 2 x Front struts (J) 2 x Rear struts (K) 1 x Handle assembly
(locking bar & R-Pin pre-tted)
(L) 4 x Wheels
(F) 1 x Front arm (G) 1 x Front axle connector (H) 1 x Rear axle assembly
(B) 2 x Cage side panels (C) 1 x Front panel (D) 1 x Cage rear panel
Fixings (Refer to the numbered steps on the card during assembling)
Please visit for our full range of accessories and consumables.drapertools.com
(M) 1 X M8 x 210mm
partial-thread carriage bolt
(Ref: Step 2)
(N) 1 x M8 x 60mm
partial-thread hex bolt
(Ref: Step 8)
(O) 4 x M8 x 20mm
carriage bolts
(Ref: Steps 4 & 5)
(P) 2 x M8 x 20mm
hex bolts
(Ref: Step 4)
(Z) 1 x Split pin
(Ref: Step 3)
(V). 4 x M12 nylon-
insert lock nuts
(Ref: Step 7)
(U). 4 x M16 x 30mm
Wheel spacers
(Ref: Step 6)
(T) 2 x M6 washers
(Ref: Step 3)
(S) 8 x M8 washers
(Ref: Steps 2,
4, 5 & 8)
(R) 5 x M12 washers
(Ref: Steps 3 & 7)
(Q) 2 x M6 x 16mm
shoulder hex bolts
(Ref: Step 3)
(Y) 8 x R-Pins
(Ref: Step 9)
(X) 2 x M6 nylon-
insert lock nuts
(Ref: Step 3)
(W) 8 x M8 nylon-
insert lock nuts
(Ref: Steps 2, 4, 5 & 8)
Product specificaties
| Merk: | Draper |
| Categorie: | Niet gecategoriseerd |
| Model: | 85634 |
Heb je hulp nodig?
Als je hulp nodig hebt met Draper 85634 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Draper
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
5 Juni 2025
5 Juni 2025
5 Juni 2025
4 Juni 2025
Handleiding Niet gecategoriseerd
- Best Fitness
- MaedHawk
- Edgestar
- ProfiCook
- Advantix
- SWIT
- Steiner
- BabyHome
- Iadea
- Rapid
- Maxview
- Reolink
- Amplicom
- ID-Tech
- Calex
Nieuwste handleidingen voor Niet gecategoriseerd
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025