Dormakaba La Gard 1947 Handleiding

Dormakaba Niet gecategoriseerd La Gard 1947

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba La Gard 1947 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Opening the lock – Using the

OPENING INDEX

The lock is shipped with the factory

combination of 50. To open, turn dial to the

LEFT passing 50 at least ﬁ ve times then

stop when 50 lines-up with the OPENING

Index. Turn RIGHT until dial stops, this will

retract the bolt.

To open the lock using a set combination,

for EXAMPLE 10-20-30-40, use the

following procedures:

Using the OPENING Index (see Figure 1)

1. Turn the dial to the LEFT (counter-clockwise) at least ﬁ ve complete rotations to clear

the lock; the lock is now ready to accept the combination. Never spin the dial to clear

the lock.

2. Using the OPENING index, turn the dial RIGHT (clockwise) passing the ﬁ rst number

in the combination [10] four times. Then stop exactly on the number [10] the ﬁ fth time.

3. Turn the dial LEFT (counter-clockwise) passing the next number in the combination

[20] three times. Then stop exactly on the number [20] the fourth time.

4. Turn the dial RIGHT (clockwise) passing the next number in the combination [30] twice.

Then stop exactly on the number [30] the third time.

5. Turn the dial LEFT (counter-clockwise) passing the last number in the combination

[40] one time. Then stop exactly on the number [40] the second time.

6. Turn the dial to the RIGHT (clockwise) to open the lock. The lock bolt is fully

retracted when the dial no longer turns right.

To lock the combination lock, turn the dial ﬁ ve complete rotations to the LEFT.

Change the combination – Using the CHANGING INDEX

To change the combination, you will need to know the existing combination and have a

LA GARD 4-Wheel change key (P/N 1315). When selecting a combination choose a four

number sequence from 0 - 99, for security purposes. It is recommended that you do not

select a combination from personal data (such as birth date, phone number, etc). Never

select numbers 0 to 20 as the LAST NUMBER of the combination; this is the “Forbidden

Zone.”

OPERATING AND CHANGING INSTRUCTIONS

4-Wheel Locks

Group 1 Locks

-205 v2 •

4/08 Kaba Mas LLC

Page 1 of 2

Figure 1

To change the combination, you must ﬁ rst open the safe door by dialing the existing

combination using the OPENING index. Note: before changing the combination verify

that the dial stopped between 90 and 0 on the OPENING index when the bolt is fully

retracted.

Setting a Combination – Using the CHANGING INDEX

Dial the existing combination as previously described using the CHANGING Index (see

Figure 1). STOP the dial on the fourth number of the combination.

1. Insert the change key into the change key

hole (see Figure 2). If the change key does

not go in easily, the wheels are not aligned

for changing. Redial the existing

combination using the CHANGING Index.

2. Turn the change key to the RIGHT until

it stops (approximately one-quarter turn).

Leaving the key in the lock, set the new

combination. EXAMPLE 10-20-30-40

3. Next turn the dial to the LEFT (counter-

clockwise) at least ﬁ ve complete rotations to

clear the lock; the lock is now ready to

accept the new combination. Never spin the dial to clear the lock.

4. Using the CHANGING index, turn the dial RIGHT (clockwise) passing the ﬁ rst number

in the combination [10] four times. Then stop exactly on the number [10] the ﬁ fth time.

5. Turn the dial LEFT (counter-clockwise) passing the next number in the combination [20]

three times. Then stop exactly on the number [20] the fourth time.

6. Turn the dial RIGHT (clockwise) passing the next number in the combination [30] twice.

Then stop exactly on the number [30] the third time.

7. Turn the dial LEFT (counter-clockwise) passing the last number in the combination [40]

one time. Then stop exactly on the number [40] the second time.

8. Turn the change key to the LEFT and remove the change key. The new combination

has been set.

To test, dial the new combination using the OPENING index. ALWAYS perform this test

with the safe door open! Test several times before closing the safe door. Also check that

the dial stops between 90 and 0 on the OPENING index when the bolt is fully retracted.

Note: When locking the safe always turn the safe handle, if present, to the locked

position (bolts extended) before turning the lock dial (ﬁ ve complete rotations to the

LEFT) to relock. If you notice any resistance DO NOT force the dial to turn. This may

cause damage to the lock.

-205 v2 •

4/08 Kaba Mas LLC

Page 2 of 2

Figure 2

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	La Gard 1947

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba La Gard 1947 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024