Dometic MILENCO AERO3 Handleiding

Dometic Niet gecategoriseerd MILENCO AERO3

Lees hieronder de 📖 handleiding in het Nederlandse voor Dometic MILENCO AERO3 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
Read these instructions carefully. These
instructions MUST stay with this product.
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
CANADA
Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
SERVICE CENTER &
DEALER LOCATIONS
Please Visit:
www.eDometic.com
RECORD THIS INFORMATION FOR FUTURE
REFERENCE:
Model Number
Serial Number
Date Purchased
Retailer / Qualied Installer
AERO WIDE
TOWING MIRROR
DM-1899
DM-2899
REVISION A
Form No. 3316479.000 10/16
©2016 Dometic Corporation
LaGrange, IN 46761
INSTALLATION
INSTRUCTIONS
2
C. Supplemental Directives
Read and follow all safety information and
instructions to avoid possible injury or death.
Read and understand these instructions be-
fore [installing / using / servicing / performing
maintenance on] this product.
Incorrect [installation / operation / servicing /
maintaining] of this product can lead to seri-
ous injury. Follow all instructions.
The installation comply with all ap MUST -
plicable local and national codes, including
the latest edition of the following standards:
U.S.A. / CANADA
● UN 46.02, Directive EC 2003/97
D. Precautions
Failure to obey the following notices
could damage product or property:
● It is recommended to take vehicle through an NOT
automatic car wash with towing mirrors attached.
Damage could result to vehicle mirrors.
This manual has safety information and instructions to help
you eliminate or reduce the risk of accidents and injuries.
A. Recognize Safety Information
This is the safety alert symbol. It is used to
alert you to potential physical injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
B. Understand Signal Words
A signal word will identify safety messages and
property damage messages, and will indicate the
degree or level of hazard seriousness.
indicates a hazardous situation that,
if avoided, could result in death or serious in NOT -
jury.
indicates a hazardous situation that,
if avoided, could result in minor or moderate NOT
injury.
is used to address practices NOT
related to physical injury.
IMPORTANT SAFETY INSTRUCTIONS
DOCUMENT SYMBOLS
Indicates additional information that is NOT related
to physical injury. Indicates step-by-step instructions.
GENERAL INFORMATION
A. Scope Of Delivery
(4) Mirror Clamp (pn DM-1960)
(2) Mirror Head (pn DM-1984)
(2) Slide Arm
(1) Storage Bag
B. Required Tools
● Phillips Screwdriver (#2)
C. Vehicle Requirements
The aero wide towing mirror will t most vehicles.
For aero wide towing mirror mounting purposes, the
vehicle mirror must have a gap between the vehicle
mirror and the vehicle mirror housing for the towing
mirror clamps to mount to. See (FIG. 1).
FIG. 1
Gap Mirror housing
Mirror
3
INSTALLATION
A. Mirror Assembly
1. Assemble mirror head to arm.
a. Using a #2 Phillips screwdriver, remove truss
head screw (4 mm x 28 mm) from mirror
head ball socket. See (FIG. 2).
FIG. 2
Mirror Head
(PN DM-1984)
Screw
(4 mm x 28 mm)
b. Slide short end of arm into hole in mirror
head ball socket, aligning cross hole in arm
with screw hole in mirror head ball socket.
Select desired arm position (right hand, left
hand, etc.). See (FIG. 3).
FIG. 3
Right Hand, Above Left Hand, Above
Right Hand, Below Left Hand, Below
NOTE: To change from right hand to
left hand, and left hand to right hand,
rotate arm in ball socket 180º.
c. Assemble screw to mirror head ball socket
and hand tighten with a #2 Phillips screw-
driver, securing mirror head to arm. See
(FIG. 4).
FIG. 4
2. Repeat steps (a) through (c) for other mirror.
B. Mirror Installation
The aero wide towing mirror can be mounted above
or below the vehicle mirror, whichever works best
for your situation. On certain vehicles, it may only
t above or below the vehicle mirror. See (FIG. 3).
1. Loosen thumb screws (“2” on thumb screw),
and remove mirror clamps from slide arm. See
(FIG. 5).
FIG. 5
“2”
“1”
Mirror Clamp
(PN DM-1960)
2. Loosen thumb screws (“1” on thumb screw).
See (FIG. 5).
3. Assemble (2) mirror clamps to vehicle mirror,
sliding “foot” of clamps between vehicle mirror
and vehicle mirror housing. See (FIG. 6).
Slide clamps in as far as possible for max-
imum clamp contact.

Product specificaties

Merk: Dometic
Categorie: Niet gecategoriseerd
Model: MILENCO AERO3

Heb je hulp nodig?

Als je hulp nodig hebt met Dometic MILENCO AERO3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Dometic

Dometic

Dometic CI-21 Handleiding

9 Januari 2024
Dometic

Dometic CMP-H1 Handleiding

9 Juli 2023
Dometic

Dometic PerfectPower PP 404 Handleiding

6 Juli 2023
Dometic

Dometic 9100 Handleiding

8 Juni 2023
Dometic

Dometic DFMD 35111 Handleiding

26 Mei 2023
Dometic

Dometic GO Hydration Handleiding

9 Mei 2023
Dometic

Dometic DFSD 12111 Handleiding

4 Mei 2023
Dometic

Dometic MILENCO AERO3 Handleiding

1 Mei 2023
Dometic

Dometic MagicWatch MWE860 Handleiding

27 April 2023
Dometic

Dometic Power Awning Handleiding

22 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024
Sony

Sony PDW-U4 Handleiding

26 April 2024
Sony

Sony NXL-FR318 Handleiding

26 April 2024