Deltronic 32-8624 Handleiding

Bekijk gratis de handleiding van Deltronic 32-8624 (5 pagina’s), behorend tot de categorie Gasmelder. Deze gids werd als nuttig beoordeeld door 63 mensen en kreeg gemiddeld 4.4 sterren uit 4 reviews. Heb je een vraag over Deltronic 32-8624 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

English

GREAT BRITAIN •customer service

tel: 08545 300 9799 e-mail: [email protected] internet: www.clasohlson.com/uk

Ver. 20131211

LP Gas alarm

Art.no 18-2447, 32-8624

The gas alarm requires 2–3 minutes to warm up whenever it is powered up. During this period

the gas alarm may not respond (no alarm) to gas or apush-button test.

Placement

For maximum protection thealarm should be installed on aflat wall in theroom where thegas

appliance is situated and agas leak is most likely to occur. In most installations this will be close

to thecooker in thekitchen or caravan etc. This gas alarm is design to detect primarily LP-gas

(liquefied petroleum gas); however it also detects thepresence of natural gas and should be

mounted differently depending on thetype of explosive gas you intend to detect.

Natural gas is lighter than air so thealarm should be installed higher than thetop of thehighest

outside window or door within aroom. This will usually be no more than 30 centimetres from

theceiling. It should also be between 1 metre and 5 metres from thegas appliance. LPG is heavier

than air so thealarm should be installed close to thelowest point, not more than 30 centimetres

from thefloor and not more than 4 metres from theappliance.

Installation

This gas alarm is design for easy installation and comes complete with screws, mounting bracket

and adaptor. Attach themounting bracket to wall with thescrews provided then twist and lock

thealarm into place (clockwise). Now choose to either plug alarm into astandard 230 V AC outlet

using provided adaptor or directly to a12 V DC source. When thealarm is properly installed,

green LED indicates thealarm is receiving sufficient power. Wait for 2–3 minutes, then push and hold

thetest button for 5–10 seconds. If thealarm is activated theunit is now ready to detect and protect.

Testing and maintenance

Test alarm by using thetest button at least once aweek and always after long absences. Check

that thegreen light diode is active, indicating sufficient current supply. Then press and hold thetest

button until thealarm sounds. Also check that thered light diode flashes during alarm test.

A simple confidence check can be conducted by using asmall disposable cigarette lighter and

Gas safety

If alarm sounds, open all windows and doors to allow thegas to disperse. Don’t switch on/off

lighting, exhausting fan or any kind of electrical appliance to avoid explosion. Check all thegas

appliances, extinguish any open flames including cigarettes and turn off thegas supply and check

hose connectors and pipes for leakages. It’s crucial that thesource(s) of theleak is determined

and appropriate repairs are made. Contact thesupplier of thegas equipment or thefire brigade if

theproblem is not located. In case of immediate danger, always call thefire brigade from outside

thebuilding.

•When leaving theroom where thegas is used, always turn off any equipment and thegas supply.

•Do not make any changes in thegas installation without proper knowledge.

•Let aspecialist inspect your gas installations regularly.

•Avoid sleeping in direct proximity to thegas installations.

Guarantee

We guarantee your new gas alarm for two years from thedate of purchase by theend user;

theguarantee is limited to replacement of theproduct, repair of theproduct or replacement of

theproduct with repaired product at thediscretion of themanufacturer.

We shall be under no obligation to repair, replace or refund units which are found to be defective

in any way due to unreasonable use or neglect, been tampered with, and modified or subject to

attempted repairs or exposed to extreme temperatures.

Alt.

12 V DC

Input rating: 100–240 V AC ~ 50–60Hz

Output rating: 12 V DC (=), 200 mA

Place mounting bracket with

arrows pointing upwards

Twist the

alarm to

install

Mark

two screw

locations

on wall

Plug in

Max 5 m

Max 30 cm

Natural GasLP Gas

Max 4 m

Max 30 cm

pressing thelever normally used to maintain theflame without

lighting it. If this is then held close to thealarm, thered LED

light will come on and thealarm will sound. Make sure to air

out theroom after testing. Vacuum unit regularly and use

acloth to wipe theoutside of thealarm. When used in for

example boats, caravans, mobile homes etc. we recommend

that you store thegas alarm in normal room temperature

during thewinter season, this prolongs its life expectancy.

A gas alarm should be replaced after around 5 years, because

thegas sensor thereafter gradually changes sensitivity.

Product specificaties