Delta Dore CV wind Handleiding

Delta Dore Niet gecategoriseerd CV wind

Lees hieronder de 📖 handleiding in het Nederlandse voor Delta Dore CV wind (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 83 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Wind Sensor
Installation instructions
The wind sensor is designed to control
outdoor blinds automatically according
to wind speed and sunshine.
This sensor is associated via wireless
with one or more receivers controlling
the different shutters in your installation.
1. How does the sensor work?
2. Description
1.1 Presentation
Wind
sensor
Protective
covers
Display
Programming
keypad
Removal
Not
used
Set wind
threshold
Association
Wind
Configuration
Wireless
transmission
signal
The sensor must be activated before
being used for the first time.
To do this, press and hold the and
buttons for 2 seconds.
The display screen will turn on.
> 2s
The wind sensor switches
automatically into energy
saving mode after 30 seconds of
inaction.
Before each use, «activate» the sen-
sor by pressing any button.
3. Activation
4. Association
1 2
> 2s > 2s
1234
... ... ...
> 3s
1234
TYXIA TYXIA
- Set the receiver(s) to
association wait mode.
- Press and hold the button for 2
seconds.
- The symbols and are displayed
while the device searches for receivers.
- The detected receiver number is displayed
on the screen,
and the symbol «NEW» appears.
- Press and hold the button to confirm
the association.
- On the receiver(s) check that the association was
successful. The receiver LED stops flashing
and the shutter briefly operates twice.
Display when the
sensor has detec-
ted more than 9
receivers.
Display when the sensor
has not detected any recei-
vers > Switches to «Manage
networks» mode (see §10)
4
OK
OFF
1234
TYXIA
Lithium battery - AA
cannot be replaced
Lithium battery life: 10 years
868,7 MHz -> 869,2 MHz
Maximum radio power < 10 mW
Receiver category: 2
100 -> 300 m
IP IPx4
-10°C / +70°C
-10°C / +60°C
260 x 104 x 130 mm
www.deltadore.com
5. Set wind threshold
> 2s
10 km/h
threshold Slight breeze
20 km/h
threshold Gentle breeze
30 km/h
threshold Moderate breeze
(default value)
40 km/h
threshold Fresh breeze
50 km/h
threshold Strong wind
66 km/h
threshold Very strong wind
To protect the shutter or blind equipment, select the wind threshold
recommended by the manufacturer.
- Press and hold the
button for 2 seconds.
- The symbol will flash.
- Press and hold the
button to select the next
value.
For safety reasons, the wind sen-
sor cannot be neutralised.
The mode is exited
automatically after
5 seconds of inaction.
7. Display of Wind Sensor setting
6. Test
The mode is exited automatically after 5 seconds of inaction.
> 2s
To test that the sensors are operating correctly.
- The sensor simulate the setting threshold and sends the required com-
mand to the receiver.
- Press and hold the
button for 2 seconds
then the button.
You can view the saved setting
1
4
2
3
- Remove the 2
protective
covers
- Replace
the protec-
tive
covers
- Straighten the
sensor
by positioning
the cups
horizontally
- Attach the sen-
sor (screws and
plugs included)
Cups
8. Installation
To remove a receiver associated with
the sensor, follow these instructions:
> 2s
1
1
2
> 2s
> 2s
- Press and hold the
button for 2 seconds.
- Press and hold the button for 2 seconds.
- The receiver number flashes for 2 seconds.
- The sensor display switches off, and the
association between
receiver 1 and the sensor is now removed.
«Manage networks» mode
- The device runs a search for associated
receivers.
- Press the button repeatedly to select
the receiver to be removed.
The associated blind will operate briefly.
9. Remove an association 10. Remove all associations
To remove all receivers associated with the sensor,
follow these instructions:
- Press and hold
the button
for 2 seconds.
- Press and hold the button
for 2 seconds.
- The display will show
then switch off.
> 2s > 2s
8.1 Location
Install the Wind sensor near
the associated blinds.
The wind sensor cups must be
positioned horizontally and facing
downwards.
8.4 Maintenance and cleaning
To ensure optimum operation of the wind/sun sensor:
• Regularly check that the wind sensor is rotating freely.
• Ensure that the sun sensor is free of dust.
If necessary, clean the cover with a damp cloth.
(Do not use abrasive cleaning products or chemical
solutions which could damage the surface of the cover.)
90°
90°
8.2 Assembly
Adapt the hinged mount to your installation.
8.3 Installation
H O2
Press and release the button to
display the value set for the wind sensor.

Product specificaties

Merk: Delta Dore
Categorie: Niet gecategoriseerd
Model: CV wind

Heb je hulp nodig?

Als je hulp nodig hebt met Delta Dore CV wind stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Delta Dore

Delta Dore

Delta Dore Tyxal+ DF Handleiding

27 Juni 2023
Delta Dore

Delta Dore Tyxal+ DOI Handleiding

21 Juni 2023
Delta Dore

Delta Dore Tyxal+ DMDR Handleiding

18 Juni 2023
Delta Dore

Delta Dore Tyxal+ DMBV Handleiding

16 Juni 2023
Delta Dore

Delta Dore DME 180 Tyxal+ Handleiding

15 Juni 2023
Delta Dore

Delta Dore DMF Tyxal+ Handleiding

12 Juni 2023
Delta Dore

Delta Dore TYXIA 6410 Handleiding

11 Juni 2023
Delta Dore

Delta Dore Tyxal+ REP Handleiding

10 Juni 2023
Delta Dore

Delta Dore Tyxal+ DFR Handleiding

9 Juni 2023
Delta Dore

Delta Dore Tybox 35 Handleiding

8 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024