De Dietrich DVH1200JU Handleiding

Bekijk gratis de handleiding van De Dietrich DVH1200JU (6 pagina’s), behorend tot de categorie Vaatwasser. Deze gids werd als nuttig beoordeeld door 92 mensen en kreeg gemiddeld 4.3 sterren uit 4 reviews. Heb je een vraag over De Dietrich DVH1200JU of wil je andere gebruikers van dit product iets vragen? Stel een vraag

1

This appliance, which is intended exclusively for domestic use, has been designed for washing

dishes.

Very important: Read all of this manual before installing and using the dishwasher. You will find the

documentation and accessories inside.

This manual is designed so that the text matches the corresponding drawing.

Instruction Manual

Identify your dishwasher model (“a”, “b”, “c”,

“d” or “e”) by comparing the control panel with

the illustrations.

1.1 Connection to the water supply (1.1.1)

The hose should run between the wall

and the bottom of the dishwasher (1.1.2),

making sure that the pipes are not twisted

or pulled too tight (1.1.3).

The water supply pressure should be

between 0.05 and 1 Mpa (0.5 to 10

kg/cm2)

If your dishwasher has a hot water intake,

you can connect the pipe to the hot water

tap. In this case, the maximum

temperature should not exceed 60ºC.

1.2 Drain. Fit the elbow supplied and

observe the levels in the drawing (1.2.1).

1.3 Connection to the mains electricity

supply. Take the information on the

nameplate (1.3) into account and never

attempt to remove it.

As this is a built-in appliance, the

electrical plug must be accessible after

installation.

1.4For fitting the dishwasher under a

worktop, first take into account the

dimensions shown in the diagram (1.4.1).

loosen and remove the leg supports

(1.4.2). Then place the dishwasher in

front of the worktop and use a

screwdriver to raise the rear leg from the

front (1.4.3), leaving a space of approx. 3

mm from the worktop.

Insert the dishwasher and ensure that the

pipes and cable do not get trapped

behind the skirting. Adjust it to the

worktop by turning the front legs (1.4.4)

and rear leg (1.4.3) until the top of the

appliance is just touching the worktop.

0Identification

1Installation

If the appliance is to form part of a row of

kitchen fittings, fit the kitchen skirting and

if opening the door interferes with it, trim the

end until the door can open properly.

If you need to fit a piece of wood to the

front, follow the instructions that come with

the appliance documentation.

For column mounting, take the height of

the drain into account (1.2.2)

2.1 Open the door and switch on the

dishwasher by pressing the button

(2.1).

2.2 Hard water. Water contains lime and its

hardness increases in direct proportion

to the quantity found.

Before using the dishwasher, you

should find out the hardness level of

the water by consulting the water

company, consulting the Technical

Support Service or using the Aquadur

strip included in the accessories bag.

Dip the stick in a glass of water for one

second. Shake it and wait for one

minute. The strip will tell you the water

hardness level according to the following

table:

This simple adjustment of the

dishwasher is vital for correct operation.

Please ensure that you do it.

Otherwise your appliance could be

seriously affected.

2Initial settings

Scale

level (HF)

Scale

level (DH)

Test

result

Dial

position

Man Elec

Hardness

0-13 HF0-13 DH

Green

No salt

needed L0Soft

1 red strip

2 red strips

3 red strips

4 red strips

Standard

Medium

Hard

Very hard

Pos. 1

Pos. 2

Pos. 3

Pos. 4

L1

L2

L3

L4

8-21 DH

22-28 DH

29-35 DH

>35 DH

14-38 HF

39-50 HF

51-63 HF

>63 HF

HF: Water hardness (French system)DH: Water hardness (German system)

Product specificaties