DCS CAD-BND Handleiding
DCS
Niet gecategoriseerd
CAD-BND
Bekijk gratis de handleiding van DCS CAD-BND (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.9 sterren uit 1.5 reviews. Heb je een vraag over DCS CAD-BND of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
1
CADBND
INSTALLATION INSTRUCTIONS
IMPORTANT!
Before you begin, read these instructions completely and carefully.
CAUTION:
Some parts have sharp edges; care must be taken when handling the various components to avoid
injury. Wear gloves when handling.
Two or more people should work together to mount the Bend Unit. CAD-BND Bend Unit must be
installed between CAD carts or Refrigerator Wrappers.
Getting Started
Remove packaging ■
Contents
Eye Goggles
Work Gloves
7/16” Socket and Ratchet Driver
7/16” Box or Open End Wrench
Screw Driver - Phillips #2
Description Qty
CAD-BND Bend Unit 1
Hex Bolt SS 1/4-20 x 1/2” 4
Washer 5/16” ID x 3/4” OD 8
Hex Nut 1/4-20 4
Tools Needed
Locating the Bend Unit:
For proper use, this product should be installed/positioned on a at ground or patio. Unevenness such as
bumps, cracks and protrusions should be 1/4” or less. If positioning the Bend Unit on uneven ground, it is
recommend to mount the CAD carts on leveling legs (CAD-LVL). If mounting to a refrigerator, the built in
leveling legs can serve the same purpose.
Before Installing:
Before you begin installing the CAD-BND Bend Unit, make note of the four sets of mounting holes located near
the top of the sidewalls. The Bend Unit is
capable of a variety of congurations that
require use of dierent mounting holes.
The top row of holes will be used when
mounting to any CAD cart; the bottom
row of holes will be used for mounting to
any of the wrappers for outdoor refrig-
eration products; the rear set of holes
will be used in the standard orientation;
the front set of holes will be used in the
reverse orientation (Fig. 01). The Bend
Unit can be mounted to all size CAD
carts as well as all outdoor refrigeration
products equipped with a wrapper.
CAD CARTS
REFRIGER ORAT
WRAPPERS
STANDARD
CONFIGURATION
REVERSE
CONFIGURATION
STANDARD
CONFIGURATION
REVERSE
CONFIGURATION
REAR
FRONT
SIDE VIEW
Fig. 01
2
The Bend Unit can be mounted in the standard orientation, with the front of the attached carts and/or refrig-
erators facing inward, or mounted in the reverse orientation. In the reverse orientation, the front of the carts
and/or refrigerators will face away from each other, giving the user more elbowroom. The reverse orientation
also provides better use of counter space, easier access to the storage space in the Bend Unit and prevents
crowding from open doors or drawers.
The side on which the door is located can also be changed for further customization. Please see the
instructions on reversing the door. This must be done before mounting the Bend Unit to any cart or refrig-
eration unit.
There are four ways to mount the CAD-BND Bend Unit. Choose your desired conguration from the pictures
below and turn to the corresponding page for mounting instructions.
* Unit shown with door in factory location (right).
** Unit shown with door in left position.
Standard Orientation with cart (see page 4)
Standard Orientation with refrigerator (see page 5)
Reverse Orientation with cart* (see page 6) Reverse Orientation with refrigerator** (see page 6)
3
Fig. 06
Fig. 07
Move latch to
other side
Fig. 05
Remove the screws from the top of the rear riser bracket to separate it from the rear wall and sidewalls 1.
(Fig. 03 and 04).
Lift rear riser o, making sure to hold the door as the hinge pin is pulled out of the door. Remove the door 2.
and riser bracket and place them out of the way.
Tilt the entire Bend Unit on its side, with the rear wall nearest the ground. Remove the screws that hold 3.
the rear wall to the sidewall and the oor panel of the Bend Unit (Fig. 05 and 06). The rear wall can now be
separated from the Bend Unit and placed o to the side.
Next, tilt the Bend Unit onto its opposite side, replace the rear wall on the other side. Using the same 4.
screws that were removed in Step 3, attach the rear wall to the opposite side of the oor panel and the
opposite sidewall. Then stand the unit up.
Before replacing the door and rear riser bracket, the latch must be 5.
moved to the hole on the opposite side of the riser (Fig. 07). No
hardware is needed.
Replace the rear riser on the Bend Unit, making sure to install the 6.
door. Drive the screws in the top of the riser to secure it to the rear
wall.
Fig. 02
Fig. 03
Fig. 04
Rear riser bracket
Rear riser bracket
Installation Instructions
Reversing Side of Door (CAD-BND)
Note: The side on which the door is located can be reversed to provide easy access and desired
positioning. This must be done before securing the Bend Unit to any supporting cart or
refrigerator (Fig. 02).
Rear wall
Product specificaties
| Merk: | DCS |
| Categorie: | Niet gecategoriseerd |
| Model: | CAD-BND |
Heb je hulp nodig?
Als je hulp nodig hebt met DCS CAD-BND stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd DCS
14 Mei 2025
18 December 2024
3 April 2024
10 Februari 2024
Handleiding Niet gecategoriseerd
- Sharkbite
- Electrify
- Winegard
- Amer
- Aukey
- Axxess
- Axor
- Zagg
- Garden Feelings
- XCell
- Voodoo Lab
- System Sensor
- E-Power
- Unicol
- Truper
Nieuwste handleidingen voor Niet gecategoriseerd
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025