Da-Lite ViewShare Advantage Retrofit 25055 Handleiding

Da-Lite Projectiescherm ViewShare Advantage Retrofit 25055

Bekijk gratis de handleiding van Da-Lite ViewShare Advantage Retrofit 25055 (20 pagina’s), behorend tot de categorie Projectiescherm. Deze gids werd als nuttig beoordeeld door 53 mensen en kreeg gemiddeld 4.8 sterren uit 27 reviews. Heb je een vraag over Da-Lite ViewShare Advantage Retrofit 25055 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/20

INSTRUCTION BOOK FOR

ViewShare Advantage Electrol Retrofit

Tools Required for Installation

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

Save These Instructions

Pre-Installation

Prior to Retroit installation, you will need to run a CAT5 or

CAT5e network cable from the motor end of your screen to

the area in which your computer will be located. THE CAT5

CABLE IS NOT PROVIDED. The length of the CAT5 cable cannot

exceed 200 feet. See Pre-Installation of ViewShare Screen and

Roller Assembly and Camera and Speakerphone Installation

sections for additional details on CAT5 cable connections.

NOTE: It requires at least two people to install a ViewShare

Retroit.

⁄“ Socket Driver

with 6" Extension

⅛” Hex Key

(included)

#2 Phillips Screwdriver

Removal of Old Screen and Roller Assembly

1. Run the screen to the up position.

2. Remove the access door by removing the screws from each end

(Figure 1). Be sure to support the door during this step to avoid

injury. Lift the door slightly and pull away from the edge of the

case.

3. Unplug 3 or 4 wire motor connector and RJ22/45 cable (if

applicable) from the junction box. See Appendix A for motor type

details.

4. Remove retainer clip from the motor (Figure 2).

NOTE: Save retainer clip for use in the installation of the

ViewShare screen and roller assembly.

5. Loosen (but do not remove) four ¼ – 20 nuts securing pin end

bracket (opposite end from the junction box) to the case housing.

While supporting the screen and roller, slide the pin end bracket

towards the end of the case and remove the existing screen and

roller assembly (Figure 3).

NOTE: Some units may only have two nuts per bracket.

¼  20 Nuts

Pin End

Bracket

¼  20 Nuts

Figure 1

Figure 2 – Motor End

Figure 3

Access Door Screws

Retainer Clip

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	ViewShare Advantage Retrofit 25055
Kleur van het product:	Black, White
Oorspronkelijke beeldverhouding:	16:9
Montagewijze:	Plafond/muur
Op afstand bedienbaar:	Ja
Zichtbare schermhoogte (h):	1470 mm
Zichtbare schermbreedte (b):	2640 mm
Diagonaal:	119 "
Type aandrijving:	Gemotoriseerd
Formaat:	HDTV
Schermgain:	1