D-Link DIR-820L Handleiding

D-Link Router DIR-820L

Lees hieronder de 📖 handleiding in het Nederlandse voor D-Link DIR-820L (4 pagina's) in de categorie Router. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

ENGLISH

12V

USB

WPS

LAN

INTER NET

POWER

12V

USB

WPS

LAN

INTERNET

POWER

12V

USB

WPS

LAN

INTERNET

POWER

DIR-820L

Wireless AC1000

Dual Band Cloud Router

If any of the above items are missing, please contact your reseller.

DIR-820L Wireless AC1000 Dual Band Cloud Router

Power Adapter

Ethernet Cable

Wi-Fi Conguration Card

Quick Install Guide

1Unplug the power to your DSL or Cable modem.

2Connect an Ethernet cable from the Internet port of the router to the

Ethernet port on your DSL or Cable modem.

3Connect another Ethernet cable from the Ethernet port on your

computer to one of the LAN ports on the router.

4Plug the power back into your DSL or cable modem. Please wait about

one minute before continuing.

5Plug the power adapter into your router and connect to an available

power outlet or surge protector. If the Power LED does not light up, press

the Power button on the back of the router.

Modem

Modem DIR-820L

DIR-820L

Computer

Modem

DIR-820L

Computer

Package Contents

Hardware Overview Minimum Requirements Connect your Router

12V

USB

WPS

LAN

INTERNET

POWER

6After the router has powered up, verify that the Power (green) and Internet

(orange or green) LEDs are both lit then continue with the Conguration

section on the other side.

Modem

DIR-820L

Computer

Ethernet Port

Ethernet Cable

Internet Port (yellow)

Ethernet Cable

• Users with DSL providers - If you are using a PPPoE connection, you will need

your PPPoE user name and password. If you do not have this information, contact

your Internet provider. Do not proceed until you have this information.

• Users with Cable providers - Make sure you unplug the power to your modem.

In some cases, you may need to turn it o for up to 5 minutes.

• Advanced Users - If your ISP provided you with a modem/router combo, you will

need to set it to “bridge” mode so the DIR-820L router can work properly. Please

contact your ISP or refer to the user manual for your modem/router device.

Before you Start

Network Requirements:

• An Ethernet-based broadband modem

Web-based Conguration Requirements:

Computer with the following:

• Windows® or Mac OS® X operating system

• An installed Ethernet adapter or wireless adapter

Supported Browsers:

• Internet Explorer 7 or higher

• Safari 4 or higher

• Chrome

• Firefox

Make sure you have the latest version of Java installed. Visit www.java.com

to download the latest version.

mydlink Requirements:

• iPhone/iPad/iPod Touch (iOS 3.0 or higher)

• Android device (1.6 or higher)

• Web Browser Requirements:

• Internet Explorer 7 or higher

• Safari 5 or higher

• Chrome

• Firefox

Note: To learn more about mydlink, visit http://www.mydlink.com.

1Power LED

A solid green light indicates a proper connection to the

power supply. The light will be solid orange during boot-up

and will blink green during the WPS process.

2Internet LED

A solid light indicates a connection to the Internet port. If the

LED is orange, the connection is good but the router cannot

connect to the Internet. If this LED is blinking orange, this

indicates that the “on demand” connection type is set and

the Internet connection is idle.

3USB Port Connect a USB ash drive to share content throughout

your network.

4WPS Button Press to start the WPS process. The Power LED will start to

blink.

5LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and

game consoles.

6Internet Port Connect your broadband modem to this port using an

Ethernet cable.

7Power Button Press to power the router on and o.

8Power Port Connect the supplied power adapter.

9Reset Button Press and hold the reset button with a paper clip for six

seconds to reset the router to the factory default settings.

ENGLISH

Cable users (DHCP) click Next to continue.

For both the 2.4GHz and 5GHz bands, create a name for your Wi-Fi Network

and a password. Your wireless devices (i.e., tablets, smartphones, and

laptops) will need to have this information entered to be able to connect to

your wireless network.

Scan the code below or search “QRS Mobile” (App Store or Google Play) to

download the QRS Mobile App to your iPhone, iPad, or Android device.

Once connected, click on the QRS Mobile icon from your mobile device,

then click Start to continue. Please follow the on-screen instructions to

complete the setup.

Once the Setup Complete screen appears, click Save and write down the

new Wi-Fi Network name and password on your companion card for future

reference.

Note: To reconnect to your router, launch your wireless utility, select the new

Wi-Fi Network you created, and then enter your new Wi-Fi password.

Version 1.1(US) | April 1, 2013 29072600820LA15

DSL (PPPoE) users enter your PPPoE user name and password supplied by

your ISP. Click Next to continue. Once your app is installed, you may now congure your router. Connect to

the router wirelessly by going to your wireless utility on your device. Scan

for the wireless network name as listed on the supplied Wi-Fi Conguration

card/sticker. Select the network and then enter the Wi-Fi Password.

Wi-Fi Name(SSID) 2.4Ghz:

dlink-2c19

Wi-Fi Name(SSID) 5GHz:

dlink-2C1B-media

Password:gccnu80856

How do I connect my wireless devices to the DIR-820L router?

1. Open your wireless network utility that displays available wireless networks.

2. Select the Wi-Fi Network name you assigned in the wizard and connect.

Note: If you did not run the setup wizard or you reset the router to its default

settings, refer to the Wi-Fi Conguration Card included for the default Wi-Fi

Network Name and Wi-Fi Password.

You can also connect using WPS:

1. Press the WPS button on the DIR-820L for three seconds.

2. Within one minute press the WPS button on your wireless device.

3. Allow up to two minutes to connect.

Note: Some devices may require you to log in to a utility to start the WPS process.

Refer to the user manual of the device you want to connect to the router if you do

not know how to start the WPS process.

How do I change the wireless settings on the DIR-820L router?

1. Open a web browser (e.g., Internet Explorer, Chrome, Firefox, or Safari) and

enter http://dlinkrouter.local./. You can also enter the IP address of the

router (http://192.168.0.1).

2. At the login screen, select admin from the user name drop-down and enter

the router password you created in the wizard (no password by default).

3. Go to Setup Wireless Settings > > Manual Wireless Network Setup to

create a new Wi-Fi network name (SSID) and Wi-Fi password.

Documentation available at http://www.dlink.com/DIR-820L.

iOS Android

Open a web browser (e.g., Internet Explorer, Chrome, Firefox, or Safari) and

enter http://dlinkrouter.local. /. You can also enter the IP address of the

router (http://192.168.0.1).

There are two ways to congure your router:

A. Web Browser - Use a web browser from your computer.

B. QRS Mobile app - Use a mobile device with the D-Link QRS Mobile app.

Refer to the QRS Mobile Setup section for more information.

When the Welcome screen appears, click Next to continue.

A. Web Browser Conguration

If the router automatically detects your Internet connection type, skip to step

5. If not, then select your Internet connection and click Next to continue.

Continue with the Setup Wizard to nish conguring your DIR-820L router.

Once completed, the Internet LED will turn green indicating that your router

is connected to the Internet.

Note: Setting up “mydlink” is optional and not required for the router to function.

Congratulations! You have completed the router installation.

Conguration B. QRS Mobile Setup Troubleshooting

D-Link Corporation or its subsidiaries in the United States and other countries. iPhone, iPad, and iPod touch are registered trademarks

of Apple Inc. Android is a trademark of Google, Inc. Other trademarks are the property of their respective owners. Maximum wireless

signal rate derived from IEEE Standard 802.11ac (Draft), 802.11g, and 802.11n specications. Actual data throughput will vary. Network

conditions and environmental factors, including volume of network trac, building materials and construction, and network overhead,

lower actual data throughput rate. Environmental factors will adversely aect wireless signal range. Product specications, size and

shape are subject to change without notice, and actual product appearance may dier from that depicted on the packaging. Visit www.

dlink.com for more details.

Having trouble installing your new product? D-Link’s website contains the latest

user documentation and software updates for D-Link products. U.S. and Canadian

customers can contact D-Link Technical Support through our website.

United States

Internet: http://support.dlink.com

Canada

Internet: http://support.dlink.ca

Technical Support

QRS Mobile App

This D-Link product includes software code developed by third parties, including

software code subject to the GNU General Public License (“GPL”) or GNU Lesser

General Public License (“LGPL”). As applicable, the terms of the GPL and LGPL,

and information on obtaining access to the GPL code and LGPL code used in this

product, are available to you at:

http://tsd.dlink.com.tw/GPL.asp

The GPL code and LGPL code used in this product is distributed WITHOUT ANY

WARRANTY and is subject to the copyrights of one or more authors. For details,

see the GPL code and the LGPL code for this product and the terms of the GPL and

LGPL.

Written Oer for GPL and LGPL Source Code

Where such specic license terms entitle you to the source code of such software,

D-Link will provide upon written request via email and/or traditional paper mail

the applicable GPL and LGPLsource code les via CD-ROM for a nominal cost to

cover shipping and media charges as allowed under the GPL and LGPL.

Please direct all inquiries to:

Email:

GPLCODE@dlink.com

Snail Mail:

Attn: GPLSOURCE REQUEST

D-Link Systems, Inc.

17595 Mt. Herrmann Street

Fountain Valley, CA 92708

GNU GENERAL PUBLIC LICENSE

Version 3, 29 June 2007

View the full GPL Code Statement at http://www.gnu.org/licenses/gpl.html

GPL Code Statement

Product specificaties

Merk:	D-Link
Categorie:	Router
Model:	DIR-820L
Kleur van het product:	Zwart
Gewicht:	291 g
Breedte:	111 mm
Diepte:	93 mm
Hoogte:	145 mm
Gewicht verpakking:	839 g
Breedte verpakking:	274 mm
Diepte verpakking:	208 mm
Hoogte verpakking:	118 mm
LED-indicatoren:	Ja
Stroom:	2 A
Wi-Fi-standaarden:	802.11a,Wi-Fi 5 (802.11ac),802.11g,Wi-Fi 4 (802.11n)
USB-connectortype:	USB Type-A
Ethernet LAN:	Ja
Meegeleverde kabels:	LAN (RJ-45)
Snelstartgids:	Ja
Inclusief AC-adapter:	Ja
Aantal Ethernet LAN (RJ-45)-poorten:	5
Aantal USB-aansluitingen:	1
USB-versie:	2.0
Aansluiting voor netstroomadapter:	Ja
Wifi-band:	Dual-band (2.4 GHz / 5 GHz)
Wifi-standaard:	Wi-Fi 5 (802.11ac)
Interfacetype Ethernet LAN:	Fast Ethernet
Ethernet LAN, data-overdrachtsnelheden:	10,100 Mbit/s
Netwerkstandaard:	IEEE 802.11a,IEEE 802.11ac,IEEE 802.11g,IEEE 802.11n
Ondersteunde beveiligingsalgoritmen:	WPA,WPA2,WPS
Ondersteunt Windows:	Ja
Upgraden van firmware mogelijk:	Ja
Ondersteunt Mac-besturingssysteem:	Ja
Rack-montage:	Nee
Bandbreedte (eerste):	2.4 GHz
xDSL-verbinding:	Nee
MAC adres filtering:	Nee
Ethernet WAN:	Ja
Spanning:	12 V
DHCP server:	Nee
DHCP client:	Nee
Network address translation (NAT):	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Bandbreedte (tweede):	5 GHz
Stateful Packet Inspection (SPI):	Ja