CyberPower ST625U Handleiding

CyberPower UPS ST625U

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower ST625U (7 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7

YOUR ULTIMATE ALLY IN POWER

Cyber Power Systems (USA), Inc.

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com

STANDBY UPS SERIES

ST425 / ST625U / ST900U

USER MANUAL

FEATURES

1. Power On Switch

2. Power On Indicator (green)

3. Battery and Surge Protected Outlets

4. Full-Time Surge Protection Outlets

5. Circuit Breaker

6. USB Port to PC (except for ST425)

7. USB Charging ports (except for ST425)

8. Widely-Spaced Outlets

Thank you for purchasing a CyberPower product. This UPS is designed to provide unsurpassed

power protection, operation, and performance during the lifetime of the product. Please take a

few minutes to register your product at: www.CyberPowerSystems.com/registration.

Registration certiﬁes your product’s warranty, conﬁrms your ownership in the event of a product

loss or theft, and entitles you to free technical support. Register your product now to receive the

beneﬁts of CyberPower ownership.

CAUTION! To prevent the risk of ﬁre or

electric shock, install in a temperature and

humidity controlled indoor area free of

conductive contaminants. (Please see

speciﬁcations for acceptable temperature

and humidity range).

CAUTION! To reduce the risk of electric shock,

do not remove the cover. There are no user-

serviceable parts inside.

CAUTION! Hazardous live parts inside can be

energized by the battery even when the AC

input power is disconnected.

CAUTION! The UPS must be connected to an

AC power outlet with fuse or circuit breaker

protection. Do not plug into an outlet that is

not grounded. If you need to de-energize this

equipment, turn o and unplug the unit.

CAUTION! To avoid electric shock, turn o the

unit and unplug it from the AC power source

before installing a computer component.

CAUTION! To reduce the risk of ﬁre, connect

only to a circuit provided with 20 amperes

maximum branch circuit over current protec-

tion in accordance with the National Electric

Code, ANSI/NFPA 70.

CAUTION! Not for use in a computer room as

deﬁned in the Standard for the Protection of

Electronic Computer / Data Processing

Equipment, ANSI/NFPA 75.

CAUTION! Do not dispose of batteries in a ﬁre.

The batteries may explode.

CAUTION! Do not open or mutilate batteries.

Released electrolyte is harmful to the skin and

eyes. It may be toxic.

DO NOT USE FOR MEDICAL

OR LIFE SUPPORT EQUIPMENT!

CyberPower Systems does not sell products

for life support or medical applications.

DO NOT use in any circumstance that would

aect operation and safety of life support

equipment, any medical applications or

patient care.

DO NOT USE WITH OR NEAR AQUARIUMS!

To reduce the risk of ﬁre or electric shock,

do not use with or near an aquarium.

Condensation from the aquarium can cause

the unit to short out.

DO NOT USE THE UPS

ON ANY TRANSPORTATION!

To reduce the risk of ﬁre or electric shock, do

not use the unit on any transportation such

as airplanes or ships. The eect of shock or

vibration caused during transit and the damp

environment can cause the unit to short out.

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting to

unpack, install, or operate your UPS.

PRODUCT REGISTRATION

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt.

The box should contain the following:

(a) UPS unit

(b) User’s manual

DETERMINE THE POWER

REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged

into the outlet does not exceed the UPS

unit’s rated capacity (425VA/260W for

ST425, 625VA/360W for ST625U, and

900VA/500W ST900U). If the rated

capacities of the unit are exceeded, an

overload condition may occur and cause

the UPS unit to shut down or the circuit

breaker to trip.

2. There are many factors that can aect

the amount of power that your electronic

equipment will require. For optimal system

performance keep the load below 80% of

the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately

upon receipt. However, after receiving a

new UPS, to ensure the battery’s maximum

charge capacity, it is recommended that

you charge the battery for at least 8 hours.

Your UPS is equipped with an auto-charge

feature. When the UPS is plugged into an

AC outlet, the battery will automatically

charge whether the UPS is turned on or

turned o.

2. With the UPS unit turned o and unplugged,

connect your equipment requiring battery

backup into the battery power supplied

outlets. Plug the other peripheral equip-

ment (printer, scanner, speakers) into the

full-time surge protection outlets.

DO NOT plug a laser printer, paper

shredder, copier, space heater, vacuum,

sump pump or other large electrical

device into the “Battery and Surge

Protected Outlets”. The power demands

of these devices will overload and possi-

bly damage the unit.

3. Plug the UPS into a 2-pole, 3-wire ground-

ed receptacle (wall outlet). Make sure the

wall branch outlet is protected by a fuse or

circuit breaker and does not service equip-

ment with large electrical demands (e.g.

air conditioner, refrigerator, copier, etc…).

The warranty prohibits the use of extension

cords, outlet strips, and surge strips.

4. Press the power switch to turn the unit on.

The Power On indicator light will illuminate

green and the unit will “beep” twice.

5. If an overload is detected, an audible alarm

will sound and the unit will emit one long

beep. To correct this, turn the UPS o and

unplug at least one piece of equipment

from the battery power supplied outlets.

Make sure the circuit breaker is depressed

and then turn the UPS on.

6. To maintain optimal battery charge, leave the

UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period

of time, cover it and store with the battery

fully charged. While in storage, recharge

the battery every three months to ensure

optimal battery life.

8. Ensure the wall outlet and UPS are located

near the equipment being attached for

proper accessibility.

9. Lay the UPS horizontally or use the key-

hole mounting slots to ax the UPS to

the wall in the proper orientation. DO NOT

stand the UPS up vertically.

Product specificaties

Merk:	CyberPower
Categorie:	UPS
Model:	ST625U
Kleur van het product:	Zwart
Gewicht:	2267 g
Breedte:	248 mm
Diepte:	81 mm
Hoogte:	147 mm
Snoerlengte:	1.5 m
Gebruikershandleiding:	Ja
LED-indicatoren:	Stroom
Vormfactor:	Compact
USB-poort:	Ja
Meegeleverde kabels:	USB-kabel
Accu/Batterij voltage:	12 V
Aantal USB 2.0-poorten:	2
Ondersteund aantal accu's/batterijen:	1
Geluidsalarm(en):	Ja
Duurzaamheidscertificaten:	RoHS, ENERGY STAR
Uitgangsvermogen:	360 W
Batterij capaciteit:	5.5 Ah
Accu/Batterij oplaadtijd:	8 uur
Temperatuur bij opslag:	-15 - 45 °C
Stroomspanning bescherming:	Overbelasting
Frequentie:	47/63 Hz
Veiligheid:	UL1778, cUL, FCC DOC B, CEC
Hoogte, in bedrijf:	0 - 3000 m
Hoogte bij opslag:	0 - 15000 m
Stekker:	NEMA 5-15P
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Batterijtechnologie:	Sealed Lead Acid (VRLA)
Surge energy rating:	890 J
Aantal AC uitgangen:	8 AC-uitgang(en)
Stopcontacttypes:	NEMA 5-15R
Output power capacity:	0.625 kVA
Ingang operation voltage (min):	96 V
Ingang operation voltage (max):	140 V
Uitgang operation voltage (min):	120 V
Uitgang operation voltage (max):	120 V
UPS-topologie:	Stand-by (Offline)
Typische backup tijd op halve lading:	9 min
Typische backup tijd op volledige lading:	2 min
Output frequentie:	50/60 Hz
Hoorbare alarmstanden:	Alarm when on battery, Fault, Low battery alarm, Overload alarm
EMI/RFI geluidsfiltering:	Ja
Spanningsbeveiliging:	Ja
Golfvorm:	Pseudo sine
USB-poorttype:	USB Type-A
Contactdoos circuitonderbreker:	Ja
Overdrachtstijd (Lijnmodus naar batterijmodus):	8 ms