CyberPower RELAYIO501 Handleiding

CyberPower Niet gecategoriseerd RELAYIO501

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower RELAYIO501 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Rela

ay Control Card

RELAYIO50

User’s Manual

K01-0000531-00

Internal Circuit

RELAYIO501 Card Pinout

Assignment Function I/O

Pin1 UPS FAULT O/P

Pin2 SUMMARY ALARM O/P

Pin3 GND (Common for Pin4) Power GND

Pin4 REMOTE SHUTDOWN Power + Vcc

Pin5 COMMON (For Relays) O/P

Pin6 BYPASS

/ UPS OFF O/P

Pin7 BATTERY LOW O/P

Pin8 UPS ON O/P

Pin9 UTILITY LINE FAIL O/P

Note: All relay contacts are normally open (N.O.) except for Pin6.

Acceptable Power + Vcc for Pin4 is 7.5 – 12V, 0.0672W Max.

For OL series UPS models only

BYPASS1 / UPS OFF

BATTERY LOW

UPS ON

UTILITY LINE FAIL

UPS FAULT

SUMMARY ALARM

GND (Common for Pin4)

REMOTE SHUTDOWN

COMMON (For Relays)

GND

Overview

The CyberPower Relay Control Card (RELAYIO501) offers users the

solution for UPS status monitoring via 5 output relays. In addition, the

RELAYIO501 card provides 1 input contact to perform UPS shutdown in

battery mode. This card is compatible with most CyberPower UPS devices

with expansion slot.

Installation Guide

The RELAYIO501 card is hot-swappable and can be installed while the

UPS is on.

1. Remove the two retaining screws on the expansion slot cover, and then

remove the cover.

2. Install the CyberPower RELAYIO501 card into the expansion slot.

3. Re-install and tighten the retaining screws.

Technical Specifications

RELAYIO501

Electrical

External S/D Voltage 7.5V – 12V

Power Dissipation 1.35W Max

(Default 12V input)

Physical

Dimensions (WxHxD) 41.8 x 14.2 x 81mm

(1.65 x 0.6 x 3.2 in)

Weight 52g (1.92oz)

Environmental

Operating Temperature 0°C – 40°C (32°F - 104°F)

Operating Humidity 0% – 95% (Non-condensing)

Output Relay Rating

Maximum

Voltage Current

30VDC / 125VAC 3A (per relay)

Function Description

Status Condition

Pin1 short to Pin5

UPS fault (Inverter Fault / DC Bus Fault / Over

Temperature / Output Short / Battery Over Charge /

Battery Test Fail

/ Fan Error

)

Pin2 short to Pin5

Summary alarm (Inverter Fault / DC Bus Fault /

Output Short / Over Temperature / Over Load /

Battery Missing / Battery Over Charge / Battery Low /

Wiring Fault / Runtime Low

/ Battery Test Fail

Load Over Setting Level

/ Fan Error

)

Pin6 short to Pin5 UPS is OFF. / UPS is in Bypass Mode.

Pin7 short to Pin5 Battery Low

Pin8 short to Pin5 UPS is on.

Pin9 short to Pin5 Utility Line Fail

For OL series UPS models only

For PR/OR series UPS models only

Example Application

Supply 12VDC to the COMMON contact and connect LEDs to the Terminal

pins 1, 2 and 6 to 9. Connect a push button to COMMON (Pin5) and

REMOTE SHUTDOWN (Pin4). Pressing the button for at least 5 seconds

will shutdown the UPS when it is on battery.

Note: When the UPS is on battery, the REMOTE SHUTDOWN input (Pin4

& Pin3) accepts at least 5 seconds of high level signal (+12VDC) to perform

the UPS shutdown. UPS output power will turn off after 120 seconds.

BYPASS1 / UPS OFF

BATTERY LOW

UPS ON

UTILITY LINE FAIL

UPS FAULT

SUMMARY ALARM

GND (Common for Pin4)

REMOTE SHUTDOWN

COMMON (For Relays)

12V

Conformance Approvals

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Important: Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

Canadian Compliance

CAN ICES-3 (B)/NMB-3(B)

Cyber Power Systems, I

nc.

Website: www.cyberpow

er.com

Product specificaties

Merk:	CyberPower
Categorie:	Niet gecategoriseerd
Model:	RELAYIO501
Kleur van het product:	Zwart
Gewicht:	52 g
Breedte:	54 mm
Diepte:	76.5 mm
Hoogte:	36.1 mm
Gewicht verpakking:	160 g
Breedte verpakking:	168 mm
Diepte verpakking:	162 mm
Hoogte verpakking:	58 mm
Certificering:	FCC B
Duurzaamheidscertificaten:	RoHS
Aantal:	1
Temperatuur bij opslag:	-15 - 45 °C
Luchtvochtigheid bij opslag:	0 - 95 procent
Hoogte, in bedrijf:	0 - 15000 m
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Code geharmoniseerd systeem (HS):	85079080