CyberPower ENVIROSENSOR Handleiding

CyberPower Niet gecategoriseerd ENVIROSENSOR

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower ENVIROSENSOR (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

Environment Sensor

ENVIROSENSOR

User’s Manual

Package Contents

Flat Head Screw (M3x20)

with Plastic Nylon Anchor

CAT5 RJ45 Ethernet Cable

(10 feet/3.05 m)

ENVIROSENSOR Hook and Loop Tape User’s Manual

Product Features

K01-0000207-00

Overview

The CyberPower environmental sensor (ENVIROSENSOR)

along with select SNMP/HTTP cards (RMCARDXXX) or most

Switched and Monitored PDUs enables users to monitor the

temperature and humidity of a server closet and/or datacenter

remotely. With CyberPower's PowerPanel Business Edition

software, users can establish thresholds that will automatically

notify users when an event has occurred via email, SMS and

SNMP traps. Additionally, the ENVIROSENSOR provides 4 input

dry contacts that enable users to monitor the status of connected

devices, such as door switch sensors.

Features include:

• Real time environment monitoring

• Remote management and configuration of the sensor via Web

Browsers or NMS

• Automatic events notification via email, SMS and SNMP traps

• 4 input dry contacts application interface provided

• Displays the name and location of the sensor and

connected devices

A. LED

B. Input Dry Contact 1-4

C. Common Connection

D. RJ45 Port

(connect to RMCARD/PDU)

NOTE: Please refer to Appendix

for Input Dry Contact Application.

DATA

STATUS

COM

41 2 3

CBD

Technical Specification

Installation Guide

Method 1- Hook and Loop Tape

Mounting

Step 1. Clean the surface of the

area where the sensor will

be installed. Apply one side

of the hook and loop tape

to the bottom of the sensor

and the other side to the

sensor location.

Step 2. Attach the sensor on the

surface and hold for about 5

seconds to ensure cohesion.

NOTE: Once the sensor is installed,

you will want to leave it in place to

ensure the the hook and loop tape

maintains its adhesiveness.

Step 3. To connect the sensor with

RMCARD/PDU, use the

attached RJ45 Ethernet

Cable. Plug one end into the

RJ45 Port and the other end

into the RMCARD/PDU.

NOTE: If the distance of

RMCARD/PDU and the sensor is

longer than 10 feet/3.05 m, use a

standard RJ45 Ethernet Cable as

needed (max 50 feet/15 m).

Universal RX/TXLink

RMCARD2 03

ENVIROSENSOR

Input Voltage 7V - 28V

Halt mode 72 mW/

Power Dissipation Normal mode 110 mW

(Default 12V input)

Measurement Range and Accuracy

Temperature 32-158 with accuracy ± 1.8 /℉ ℉

0-70 with accuracy ± 1℃ ℃

Humidity 10-90 RH with accuracy ± 2%

Communication

Connection Port RJ45 Port

Input Dry Contact 4

Physical

Dimensions (L x W x H) 2.32 x 1.77 x 1.14 inches/

59 x 45 x 29 mm

Weight 1.46 oz /41.5 g

Safety Approvals FCC Class B, CE, C-Tick

Warranty 3 Year Limited

Method 2- Fixed Mounting

Step 1. Drill a hole that is

compatible with the

anchor and insert the

included anchor.

Step 2. Insert and tighten the

screw into the anchor.

Leave enough of the

screw exposed for the

sensor to be mounted to.

Step 3. Hang the sensor

horizontally or vertically.

Step 4. To connect the sensor

with RMCARD/PDU, use the

attached RJ45 Ethernet Cable.

Plug one end into the RJ45

Port and the other end into

the RMCARD/PDU.

HoleØ6mm(0.24in)

For further configuration

information, please refer to the

RMCARD/PDU user’s manual.

Universal RX/TXLink

RMCARD2 03

Conformance Approvals

FCC Warning

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does not cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

This device compiles with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR

ANY RADIO OR TV INTERFERENCE CAUSED BY

UNAUTHORIZED TO THIS EQUIPMENT. SUCH

MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

Troubleshooting

The RMCARD/PDU

is not able to acquire

environment sensor's

information.

Check the LED.

When the connection is ok, the LED

should always be on; otherwise,

ensure the RJ45 Ethernet cable is

correctly connected to the

RMCARD/PDU and sensor.

Note: Do not use a crossover cable

which is for Tx/Rx.

The Input Dry

Contact does not

function correctly.

Ensure the Input Dry Contact wires

are correctly connected and make

sure the open/short circuit setting of

the connected devices is the same

as the setting on the Web Interface.

Problem Solution

CyberPower North America

CyberPower Systems (USA), Inc.

Phone: (952)-403-9500 Toll-free: (877)297-6937

4241 12th Avenue E. Suite 400, Shakopee, MN 55379

E-mail: tech@cpsww.com

Website: www.CPSww.com

CyebrPower Europe

CyberPower Systems, Inc.

E-mail: sales@cpsww.eu

Website: www.cpsww.eu

CyberPower Systems France

Z.I. Saint Séverin 28220 CLOYES sur le Loir – France

Tél: +33(0)2 37 98 61 50

E-mail: sales@cpsww.com.fr

Dry Contact

External Sensor 1/2/3/4

COM

1 2 3 4

Appendix

Input Dry Contact Application

Do not input signals that carry

voltage into the input dry

contacts. The input dry contacts

only allow for open/short circuit.

Product specificaties

Merk:	CyberPower
Categorie:	Niet gecategoriseerd
Model:	ENVIROSENSOR
Kleur van het product:	Grijs
Nauwkeurigheid:	1 °
Spanning:	12 V
Code geharmoniseerd systeem (HS):	85079080