CyberPower CPS3000EILCD Handleiding

Bekijk gratis de handleiding van CyberPower CPS3000EILCD (2 pagina’s), behorend tot de categorie Zonnepaneel. Deze gids werd als nuttig beoordeeld door 9 mensen en kreeg gemiddeld 4.8 sterren uit 9 reviews. Heb je een vraag over CyberPower CPS3000EILCD of wil je andere gebruikers van dit product iets vragen? Stel een vraag

CPS00EILCD 30

User’s Manual

IMPORTANT SAFETY INFORMATION

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting to unpack,

install, or operate the INVERTER.

Insure the wall outlet and INVERTER are located near the equipment being attached for proper

accessibility.

To reduce risk of damage and injury, please use batteries th good quality. wi

Provide adequate ventilation for the battery compartment. The battery enclosure should be designed to

prevent accumulation and concentration of hydrogen gas at the top of the compartment.

DO NOT expose the INVERTER to rain, snow or liquids of any type. TINVERTER is designed for he

indoor use only.

DO NOT obstruct the ventilation openings.

DO NOT connect neutral of the power distribution box on the wall to:

(a) The OUTPUT neutral of INVERTER .

or (b) The INPUT neutral of equipment.

Otherwise the reversed polarity will damage the INVERTER and the connected equipmen t.

CAUTION! Risk of electric shock, do not remove cover. No user serviceable parts inside.

The battery can energize hazardous live parts inside even when the AC input power is disconnected.

To avoid electrical shock, turn o the INVERTER and unplug it from the AC power source before

servicing the battery. Servicing the battery can only be performed by trained personnel.

To avoid electrical shock, install the metal cover of the terminal block after the AC input and

output is connected.

INSTALLING YOUR INVERTER SYSTEM

UNPACKING

Inspect the unit upon receipt. The box should contain the following:

INVERTER Unit1; Power Cord1; User Manual1 

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Insure that the equipment plugged into the outlet does not exceed the INVERTER ACunit’s rated

capacity (00VA/10W for CPSILCD If rated unit capacities are exceeded, an overload 30803000E).

condition may occur and cause the INVERTER unit to shut down or the circuit breaker trip.

2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert

Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only

calculates the maximum amount of VA that the equipment can use, not what is typically used by the

equipment at any one time. Users should expect usage requirements to be approximately 60% of

below value.

TO ESTIMATE POWER REQUIREMENTS

1. 220 V x Amps (A) = VA

2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual

requirementsThere are many factors that can aect the amount of power that your computer system .

will require. The total load that you will be placing on the battery-powered outlets should not exceed

80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

Before installation, please read and understand the following instructions:

1. Placement

The INVERTER must be installed in a protected environment away from h- emitting appliances eat

such as a radiator or heat register. Do not install this product where excessive moisture is present.

2. Ventilation

The location should provide adequate air ow around the INVERTER with 10 CM minimum

clearance on all sides for proper ventilation.

3. Connect the Battery

Connect the external battery with the DC cables

from the back of the INVERTER. Follow battery

polarity guide located near battery cables as

below.

+“”Red cable for battery positive polarity;

“”- Black cable for battery negative polarity.

4. Connect to AC and Charge the Battery

Connect the INVERTER to a wall outlet using extension cordsTo be connected well, the ends of .

the cords which connect the inverter should be compressed into the attached pin terminals. The

wire diameter should not be less than 1.3mm

2

.

. Charging the battery for at least 8 hours is recommended to insure that the battery is fully charged.

To recharge the battery, simply leave the unit plugged into a wall outlet. To maintain optimal battery

charge, leave the INVERTER connect an AC outlet at all times.

This INVERTER can be charged even when INVERTER is not turn edon.

5. Connect the Load

Connect the equipment to the INVERTER outlet using extension cordsTo be connected well, the .

ends of the cords which connect the inverter should be compressed into the attached pin terminals.

The wire diameter should not be less than 1.3mm

2

.. Please make sure that the total loads of your

equipments are less than the maximum total power load of the INVERTER. Screw the terminal

block cover onto the inverter nally.

BASIC OPERATION

FRONT PANEL DESCRIPTION

1. LCD Module Display.

High resolution and intelligent LCD display shows all the INVERTER information with icons and

messages. For more information please check the “Definitions for Illuminated LCD Indicators”

section.

2. Power Switch

Press the power switch to turn the INVERTER ON or OFF.

3. LCD Function Selected Switch

The switch can be used to select the LCD display contents including input/output voltage and load

percentage, etc.

REAR PANEL DESCRIPTION

4. DC Input Cable (Black)

Connect to battery negative polarity.

5. DC Input Cable (Red)

Connect to battery positive polarity.

6. Input Circuit Breaker

Thecircuit breaker provides optimal overload protection.

Product specificaties