CyberData Systems 011324 Handleiding

CyberData Systems Receiver 011324

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberData Systems 011324 (3 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 1355 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

Quick Start Guide 931155B

The IP Endpoint Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operations Guide,

which is available in the Downloads tab at the following webpage:

https://www.cyberdata.net/products/011324/

Note You can also navigate to the Downloads tab by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

IEEE 802.3af or 802.3at PoE Switch IEEE 802.3af or 802.3at PoE Injector

Set PoE power type to Class 0 = 15.4W

for high power PoE+ set Class 4 = 30W

CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

SIP

OUR PRODUCTS

VOIP PRODUCTS

011324 SIP PAGING AMPLIFIER Downloads

SIP Paging Amplifier

Quick Start Guide

Quick Start Guide 931155B

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device during the initialization process. See the following figure:

3.2. The Power (Pwr) LED is GREEN for 802.3af and is BLUE for 802.3at. The

GREEN Status LED and the GREEN Power (Pwr) LED come on

immediately. The Speed (SPD) LED illuminates AMBER for a 100Mb link or

is off for 10MB when the network link to the device is established. The Link/

Activity LED blinks to indicate network traffic.

After about 20 seconds, the GREEN Status LED will blink fast to indicate

that the device is acquiring an IP address and attempting to autoprovision.

It will turn off thereafter until the device has finished booting. When the

device has fully booted, the GREEN Status LED will turn on solid.

If there is no DHCP server available on the network, it will try 12 times for 60

seconds and eventually fall back to the programmed static IP address (by

default 10.10.10.10) or the previously used DHCP address if a prior lease

was established. This process will take approximately 80 seconds.

3.3. When the device has completed the initialization process, press and hold

the RTFM switch for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

SPD

PWR

Link/Act

Status

Volume

Power (Pwr) LED

( )BLUE/GREEN

Speed (SPD) LED

(AMBER) (100Mb)

Link/Activity (Link/Act.) LED

( )GREEN

Status LED

( )GREEN

Quick Start Guide 931155B

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• Computer

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a computer that is connected to the same switch

as a single CyberData device. Note the subnet of the test computer.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the following

link:

https://www.cyberdata.net/pages/discovery

4.3. Wait for initialization to complete before using the Discovery Utility program

to scan for a device. The device will show the current IP address, MAC

address, and serial number.

4.4. Select the device.

4.5. Click Launch Browser. If the IP address is in a reachable subnet from the

computer that you are using to access the device, the Discovery Utility

program should be able to launch a browser window pointing to the device’s

IP address.

4.6. Log on to the web interface by using the default username (admin) and

password (admin) to configure the device.

4.7. Perform an audio test by pressing the Test Audio button that is located at

the bottom of the Device Configuration page. If the audio test message is

clearly audible, then your CyberData device is functioning properly.

4.8. The device is now ready to be set for your desired network configuration.

You may search the Compatible IP-PBX Servers index for available

sample VoIP phone system configurations and set up guides at the following

website address:

https://www.cyberdata.net/pages/connecting-to-ip-pbx-servers

Product specificaties

Merk:	CyberData Systems
Categorie:	Receiver
Model:	011324
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	630 g
Breedte:	83.7 mm
Diepte:	26.5 mm
Hoogte:	198 mm
Gewicht verpakking:	900 g
LED-indicatoren:	Ja
Stemcodecs:	G.711alaw, G.722, G.729
Connectiviteitstechnologie:	Bedraad
Type stroombron:	Power over Ethernet (PoE)
Certificering:	CE; EMC Directive - Class A EN 55032 & EN 55024, LV Safety Directive- EN 60950-1, RoHS Compliant, FCC; Part 15 Class A, Industry Canada; ICES-3 Class A
Duurzaamheidscertificaten:	CE, RoHS
Ethernet LAN, data-overdrachtsnelheden:	100 Mbit/s
Temperatuur bij opslag:	-40 - 70 °C
Audio-uitgangskanalen:	- kanalen
Naleving van duurzaamheid:	Ja
Lijnuitgang:	Ja
Signaal/ruis-verhouding:	- dB
Ondersteunde protocollen:	SIP RFC 3261
Totale harmonische vervorming (THD):	0.5 procent
Bedrijfstemperatuur (T-T):	-40 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Piekvermogen per kanaal:	- W
Synchronisatie ingangsimpedantie:	10000 Ohm
Output impedance:	10000 Ohm