CTA Digital PAD-GCADMH Handleiding

Bekijk gratis de handleiding van CTA Digital PAD-GCADMH (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.6 sterren uit 3 reviews. Heb je een vraag over CTA Digital PAD-GCADMH of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Package Contents:

Instructions:

1.

Setting Components for Mounting

Setting Up Grommet Clamp Mount Installation

2.

6.

Adjusting VESA Joint for Tilt, Swivel &

Orientation Adjustability

7.

Cable Routing & Tool Management

Setting Up Direct Grommet Mount Installation

3.

4.

Placing VESA Mount on Pole

5.

Connect VESA w/ Non-Security Holder

M

PAD-GCADMH

INSTRUCTION - MANUAL

Desk Grommet Mount

with Non-Security Universal Holder

(x4)

N

888-733-4448

888-733-4448

1A. Take the body pole endcap (J) and place it on the top end of the

body pole (A) as illustrated above.

1B. Take the top half of the grommet clamp (C) and place on the (4)

pads (I) underneath as shown. Peel off the sticker backing, and with

the adhesive side facing the clamp, place it on securely.

2A. Align the bottom end of the body pole

(A) with the canopy (B) and with the top

piece of the clamp (C).

A

B

C

2B. Using a powerdrill tool (not included), drill a 10mm diameter hole through the surface you

wish to mount into. Take the knob screw component (E) and the bottom piece of the clamp (D)

from below and align with the top side components from step 2A. Then rotate the knob with

bottom piece until securely tightened.

E

D

A

B

C

H

L

3A. Align the bottom end of the body pole (A) with the canopy (B) and with the top piece of

the clamp (C). Then rotate in screw (H) from below using provided tool (L) until securely

tightened as illustrated above.

3B.Take the assembled body

comination and place it on the surface

top. Lift up the canopy to see drill

holes. Then drill in (4) screws in the

screw holes until securely tightened

with screwdriver or powerdrill. (Both not

provided). Slide canopy back down

over the top clamp piece.

K

F

4A. Using the provided tool (K), loosen the

stopper component on the body pole to raise or

lower until desired height. This will prevent any

other other components from sliding down. Once

desired height is set, tighten stopper component

with tool until securely fastened.

4B. Take VESA mount pole

mount (F) and slide it from

above onto the body pole

(A). Slide it down until it

rests on the stopper. Take

the provided tool (K) and

tighten as illustrated until

securely fastened.

K

5A. Align clamp mount VESA plate (F) with the VESA plate of the

tablet holder (N). Then using the provided tool (P), rotate in

screws (M) from the front while holding the hex nuts (O) from

behind with your hand. Do this for all (4) screws until securely

tightened.

O

(x4)

M

O

N

F

P

(x1)

P

6A. Align clamp mount VESA plate (F) with the VESA plate of the tablet holder (N). Then using

the provided tool (P), rotate in screws (M) from the front while holding the hex nuts (O) from

behind with your hand. Do this for all (4) screws until securely tightened.

L

L

K

7A.Identify cable management clip / tool organizer on the body pole

(A). When fishing your wire from the tablet/device towards the power

source, hook onto the clip to aid in neatly routing the cable. Also on

the side of the clip, you can find two tool holders to help put away

provided tools (L, K) as illustrated above. When angle adjustments

are needed and joints need to be loosened, it provides quick access

to the needed tools.

M5x12

M5 Nut

M5 Allen

Key

Product specificaties