Cresta DTX600 Handleiding

Cresta Weerstation DTX600

Lees hieronder de 📖 handleiding in het Nederlandse voor Cresta DTX600 (11 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/11

DTX600 WEATHERSTATION USER MANUAL

Thank you for purchasing this device, Please read the operating instructions carefully to

familarize yourself with the features and modes of operation before using the instrument.

Package Contents

Carefully unpack and remove the contents:

•1x weather station main unit

•1x stainless steel mast

•1x thermo-hygro sensor

•1x rain sensor

•1x wind speed sensor

•1x wind direction sensor

•Mounting screws

•Stainless steel accessory for fixing the mast and screws.

Technical Details

•Six keys: MODE, +, -, ALARM, ALERT,SNOOZE/LIGHT

•Radio controlled clock

•Automatic receiving of time signal DCF77 to display exactest time

•Automatically switches to/from daylight saving time (summer/winter time)

•Time display in 12/24 format

•+/-12 total 24 adjustable time zones

•Continuous perpetual calendar up to 2099

•Display of D , Month Day of weekate and

•Day of week display available in 7 languages, i.e. German, English, Italian, French, Dutch

Spanish,Danish.

•Dual alarm with snooze function (5 minutes alarm interruption)

•5 weather forecast: sunny, partly sunny, cloudy, rainy, storm .

•Barometer and bar of 12 hours history for air pressureand data

•Indoor /outdoor temperature and humidity with trend

•Max./min. of temperature and humidity

•Thermometer measuring range inside:°C to +50 °C , outside -20 ~60°C °C

•Temperature display elective in °C or °F

•Temperature alert for indoor and outdoor

•Living space humidity

•Moon phase

•Wind speed in mph /kmh wind speed 0~256kmh，

•Wind direction in 16 directions

•Rainfall in mm and inch and display of 1hour, 24hour, TOTAL.

Rain volum 0~999.9MM：（）

•·Low battery indication

•B ackground illumination LED.lue b

•Main unit b 2 x AA, LRatteries: 06, 1.5V

Outdoor sensor:

•Frequency: 433 MHz

•Transmission range: 100 meters in open area.

** Actual distance may be varied depending upon the enviroment, it will be shortened if with

interference ,such as concrete wall etc.

•Batter : 2 x AA, LRies 06 1.5V

Installation

•Installing the Batteries

•Open the main unit battery cover located at the back of the unit and insert 2XAA batteries

into the battery compartment and close the battery cover.

•Pull away the shower proof casing of the thermo-hrgro sensor to reveal the 2 sockets.( for

the wind sensor and rain sensor )

•Connect the attached cables 1.cable from wind speed sensor insert into the socket of wind

direction sensor 2. cable from wind direction and cable from rain sensors to the

corresponding sockets of the thermo-hygro sensor by clicking them into place. Make sure

that rain and wind cables are connected to the correct sockets.

NOTES:

•First insert the batteries of main unit, then insert the batteries of the outdoor sensor in 3

minutes after the main unit is powered on, to assure of the sensor data received well.

In case of the outdoor sensor data received failure, pls press key for more than 3 ALARM

seconds to synchronize the RF signal.

•Every time the batteries are replaced , the main unit will loose all the weather data.

•

•Every time the batteries are replaced , the thermo-hygro sensor will sychronize with the main

Unit again.you must press the key for more than 3 seconds to synchronize the RF ALARM

signal.

•In case of any failure of RF, pls reset the sensor to and press receive again.ALARM

•Mounting the main unit

The main unit can be placed onto any flat surface or wall mounted at the desired location by

Hanging hole, It is important to check that the radio signal can be received before mounting.

•Mounting the outdoor sensor onto the stainless steel mast

For accurate results, the outdoor sensor mast should be securely mounted onto a horizontal

surface and in an open area away from trees and other coverings where rainfall or wind

speed may be reduced causing inaccurate reading.

1. Mounting the wind speed sensor to the first plastic bracket：first check the wind-fan

can rotate freely before fixing . The wind speed sensor should now be mounted onto the

bracket provided to allow the wind to travel around the sensor unhindered from all

directions.please follow the below display :

2. : first check the wind Mounting the wind direction sensor to the first plastic bracket

direction sensor before fixing,there is one cable from wind speed sensor, please insert it

into the socket under the wind direction sensor.please follow the below display:

Product specificaties

Merk:	Cresta
Categorie:	Weerstation
Model:	DTX600
Kleur van het product:	Zwart
Klok functie:	Ja
Meetfuncties:	Anemometer (windsnelheid)
Type batterij:	AA
Aantal batterijen (receiver):	2
Aantal batterijen (sensor):	2